Coil spring isolator install without removing coil springs?
#1
Newbie
Thread Starter
Join Date: Jun 2011
Location: Oregon
Posts: 8
Likes: 0
Received 0 Likes
on
0 Posts
Year: 2000
Model: Cherokee
Engine: I6 4.0
Coil spring isolator install without removing coil springs?
I was wondering if anyone has done this before or has any theories on how it could be done. The front of my jeep is slightly lower than the back and the back has had plenty of time to sag. I would like to add an extra coil spacer to bring it up a little. I can take them out as i already did to do my budget boost, but if there is a way I can me lazy and do it fast that would be great.
I have thought about trying to slip it in and twist it up the spring but at the end the spring closes. I do not have the coil isolators yet but are the stock ones flexible enough to cut through and twist them to the point that you can slip them over the shaft that holds the bump stop?
Just curious and didn't see a post about it.
Thanks
Ben
I have thought about trying to slip it in and twist it up the spring but at the end the spring closes. I do not have the coil isolators yet but are the stock ones flexible enough to cut through and twist them to the point that you can slip them over the shaft that holds the bump stop?
Just curious and didn't see a post about it.
Thanks
Ben
#4
Newbie
Thread Starter
Join Date: Jun 2011
Location: Oregon
Posts: 8
Likes: 0
Received 0 Likes
on
0 Posts
Year: 2000
Model: Cherokee
Engine: I6 4.0
If i made one cut through I should be able to get it in there though. Arent they made of a hard rubber that I can bend to some extent to get it in and once its in there it wont get bent to a point were it will come out?
I just like the simplicity of it and ease.
I just like the simplicity of it and ease.
#5
CF Veteran
Join Date: Mar 2010
Location: Jacksonville, FL
Posts: 6,685
Likes: 0
Received 5 Likes
on
5 Posts
Year: 92
Model: Cherokee
Engine: 4.0
Originally Posted by Laxman30
If i made one cut through I should be able to get it in there though. Arent they made of a hard rubber that I can bend to some extent to get it in and once its in there it wont get bent to a point were it will come out?
I just like the simplicity of it and ease.
I just like the simplicity of it and ease.
It gets its strength from being a complete piece
#7
Trending Topics
#8
Senior Member
Join Date: Dec 2010
Location: Orlando-Miami
Posts: 1,358
Likes: 0
Received 0 Likes
on
0 Posts
Year: 1993
Model: Cherokee
Engine: 4.0 HO
?? The way I'm talking only needs to compress the spring about 1". My local dental surgeon will not need to know me. Sorry you don't have droop.
OP's jeep isn't lifted very high so this method can probably work out.
OP's jeep isn't lifted very high so this method can probably work out.
#9
Member
Join Date: Aug 2011
Location: Ramona, CA
Posts: 123
Likes: 0
Received 0 Likes
on
0 Posts
Year: 1990
Model: Cherokee
Engine: 4.0
I just flexed my Jeep tell the spring fell out of bucket... if u have short arms u have to disconnect the lca... in this pic if I unbolted the bottom spring holder I could get my spring out
#10
Newbie
Thread Starter
Join Date: Jun 2011
Location: Oregon
Posts: 8
Likes: 0
Received 0 Likes
on
0 Posts
Year: 2000
Model: Cherokee
Engine: I6 4.0
Ok I will most likely just take the springs out I just wanted to see if I could do it effectively without. I like working smarter instead of harder but might as well do it the right way.
Thanks guys
Thanks guys
#11
CF Veteran
Join Date: Mar 2010
Location: Jacksonville, FL
Posts: 6,685
Likes: 0
Received 5 Likes
on
5 Posts
Year: 92
Model: Cherokee
Engine: 4.0
Originally Posted by My375hp302
Thats a good way to make your local dental surgeon very happy. Use a spring compessor and save your teeth.
#12
Originally Posted by My375hp302
Thats a good way to make your local dental surgeon very happy. Use a spring compessor and save your teeth.
#13
CF Veteran
Join Date: Feb 2011
Location: Long Beach, Ca
Posts: 3,500
Likes: 0
Received 0 Likes
on
0 Posts
Year: 2000
Model: Cherokee
Engine: 4.0 I6
Originally Posted by dogger15
A spring compressor is way worse. It can do more then mess up your teeth. Best way just dis connect shocks and what not and jack up the front enough to take the coils out
Thread
Thread Starter
Forum
Replies
Last Post
ROCKRIDGE 4WD
Vendor Showcase
0
08-28-2015 12:28 PM
Currently Active Users Viewing This Thread: 1 (0 members and 1 guests)