Ralph77

So the Jeep is done inside. Not that you can tell. I added a little fake wood grain trim that I picked up awhile back. Thanks to USN_JeepXJ posting the part number I put those little rubber bumpers in the console lid. Definitely helps with the movement. Dorman 45393 or at Napa BK665-1478. I could not get them in though without trimming the part that is countersunk. I finally got around to soaking the emergency brake adjustment in PB Blaster and covering with Fluid Film since the power washing underneath. I keep it like that all the time.

jessenator

Now all I need to do is get the rest of the jeep working...

Bugout4x4

I always liked those, not only for looks, but with all that webbing they appear to be stronger than most alloy wheels.

Martlor13

you finally found a trade partner?

jessenator

I love these way more than the diamond spoke wheels, which is what was on it. Plus they were nasty and painted (not very well)


Yup! On KSL (the thing Utahns use instead of CL). Only had to pay for his mount and balance, which wasn't bad.

88laredomudtoy

RocketMouse

You'd know if you had a cracked head pretty easily... check the oil. If you've got coolant mixed in it... then I'd say yep.

XJwonders

Tore the 4.0L apart today

Ozalid

Found out this morning after compression test...either blown head gasket or cracked head...... . if head , Im thinking about a referb ...
I kind of knew going in on this that it had motor.problems....After I got it running, I got my hopes up.... But--. 140,90,120,90,70,130 ...I cant believe it runs as well as it does..

RocketMouse

On mine... tomorrow... going to take off the throttle body assembly, and IAC... give them all a good through clean, as I doubt the PO ever did it.

Ralph77

So today I want to detail the outside. Now realize I don't have a clue. Usually do it by hand. Mostly Turtle Wax stuff. Rubbing compound on the rougher spots here and there. Like behind the door handles where you finger nails scratch it up. Polishing compound every where else. Mother's Back To Black for the trim and whatnot. Finish with some wax. RainX the windows. It is a Jeep not some classic car. The Mother's Clay bar kit was on sale so I decided to give it a try. Probably will only be a one time thing even if I do like it. Remember Jeep not classic car. Well I decided to invest in some power tools. Picked up the HF Dual action polisher to use with the Meguire's Ultimate Compound that a fellow forum member recommended. Grabbed all the pads and whatnot just to have. Thinking I will use the polishing one with the Meguire's. I also picked up a 3" dual action polisher to use with the Back To Black. I am tired of the stuff running down the side of the Jeep. My hands are not what they used to be so I am hoping a little bit more buffing might tone that down. If that doesn't work out, machine does look like a piece of crap, I bought the stuff to attach to my drill to hopefully achieve what I am trying to do. Still going to hit the more problem areas with the rubbing compound by hand. Then apply the wax with the HF tool.

I tried to research how to do this properly. Internet is full of stuff but everybody has their own way. I gleaned as much as I could, set up a plan of attack, and it is what it is. LOL.

4WD4EVER

RM, have you tried this trick yet? If not, I recommend it:

https://www.cherokeeforum.com/f30/st...-4-0-a-226299/


Yes, Ralph, the amount of info on detailing can be overwhelming, but, I'll share a couple tips:

Use the least aggressive pad & product combo it takes to achieve the results you want. This prevents you from doing an area twice. For example, if you are trying to remove fine swirls, don't use rubbing compound and/or a coarse pad or wool.

Apply the product to small sections (2'x2'), work it through 3-4 passes with overlap and remove. Dried product is tough to remove so, small sections prevent creating more work.

For compounds, use higher speeds (5-6). For waxes, use
lower speeds (1-2).

Clay the windows. Yes, the windows. It is amazing how much foreign material/environmental fallout gets embedded in auto glass and claying is a great way to remove it.

Good luck.

p.s. I know you're not looking to achieve show-quality results but I thought I'd share a black GMC truck I did for a friend several years ago and the results I achieved. Black is alot of work and I don't do anyone's vehicles but my own but is beautiful when done:





The specks are just dust.

investinwaffles

I've been detailing professionally for 12+ years, it's definitely not easy - lots of elbow grease.

What are you having issues with as far as the D/A (dual-action) polisher? The Harbor Freight one I have heard is fairly good actually - just take it apart and re-pack it with good quality grease at some point. Youtube has tons of videos how to do that


In regards to proper polishing technique, it looks like you have 3 pads - orange, blue and black (in order of most to least aggressive). The black pad should have zero cut and would be for wax/sealant at the end.

On most cars "start with the least aggressive pad" but on an XJ - just go for an orange pad out of the gate.

Priming the pad is very important, or else you will have spots with more/less compound on the pad and will polish unevenly. Prime the pad by putting 4-5 pea sized dots of product on, and rubbing it in with your finger. I will then mist the pad with some quick detail spray to help keep things lubed up. Detail spray can be spritzed on the pad to increase the working time of the compound/polish.

Work the polish in at speed 1-2 initially, then increase to speed 3-5, then continue to polish until it starts to become clear. Repeat with the blue pad and your finishing polish, then wipe down the panel with Isopropyl Alcohol and throw some wax on there.

Watch some youtube videos, it will give you a visual overview of the technique. It's not difficult, just labor intensive.

Because your XJ has probably never been polished - the pads are going to "load" up with paint very quickly. You can clean the pads with degreaser, a soft brush, and water but they can't be that wet when you are polishing or it will add too much lubrication to the surface and the polish wont cut properly.

My favorite method is to polish the panel, let the pad dry for a few minutes, and turning it on to speed 1-2 and using either a fingernail brush or an air compressor to clean the dried compound/paint off the pad. Then sometimes I will grab a damp microfiber and scub the face of the pad down if there are any clumps left.

EDIT:

My go to combo for heavy oxidation is M105 on a microfiber cutting pad, and M205 on a White or Green pad. Then I will either finish with Collinite 845 or Klasse AIO (lots of fillers, hides any remaining scratches) topped with 845.

Ralph77

With the Meguire's I am going to use the HF Polishing (blue) pad.

Thank you for that info. I just plugged it in and was kinda wondering what speeds to use. 6 is the highest.

I uesd the RainX stuff once. After seeing a car show when they were showing, I think, the Mother's stuff. Was like $60. RainX was more like $12. It did a good job. Problem was it does not hold. I hardly drive and after a short period of time using the baggie trick I could feel the particulates on the windshield. When I first did it it was baby bottom smooth using the baggie trick. So I blew that off. Maybe next time if there is a next time for claying.

It will be what it will be but thank you for the advice.

investinwaffles

I removed my side moulding this morning, looks a lot better than it did. Then I washed it and I think I am going to throw a coat of wax on it because the last few posts inspired me