What did you do to your Cherokee today?
Newbie
Joined: Mar 2012
Posts: 11
Likes: 0
From: Fort Wayne, IN
Year: 1999
Model: Cherokee
Engine: 4.0l
rust
Installed new thermostat and heater hoses, flushed rust from cooling system and degreased engine bay. Put the damn thing in the air to degrease bottom half, only to discover a huge gaping hole in the drivers floor board 
(dont know how I missed that the last time I had it in the air 
). I wondered why the floor board would freeze in the winter after the inside cooled down. I only drove this a few times last winter, as it was my in-laws backup vehicle and decided to buy it.
Luckily my buddy owns a bodyshop and told me to take out the interior and he would patch it for me. Oh, and it's weird how this portion of the floor board is so bad and the rest is damn near perfect
.
(dont know how I missed that the last time I had it in the air ). I wondered why the floor board would freeze in the winter after the inside cooled down. I only drove this a few times last winter, as it was my in-laws backup vehicle and decided to buy it. Luckily my buddy owns a bodyshop and told me to take out the interior and he would patch it for me. Oh, and it's weird how this portion of the floor board is so bad and the rest is damn near perfect
.
Last edited by cpnscrvy; Apr 4, 2012 at 01:24 PM. Reason: misspelled
Seasoned Member
Joined: Jan 2011
Posts: 474
Likes: 0
From: brandenburg ky
Year: 1990
Model: Cherokee
Engine: I6
Pulled the alt. off my wife's 87 to put it on my90 seeing how the alt. locked up on me in town today good thing I keep my tools in my jeep
All this done in about 2 hours
All this done in about 2 hours
CF Veteran
Joined: Dec 2010
Posts: 1,240
Likes: 0
From: Rocket Country MI
Year: 1999
Model: Cherokee
Engine: 4.0
hauled 16 8ft 2x3, 8 8ft 2x4 and 4 4x8 sheets of plywood from the depot to my office to build some shelves. no pics but it was all inside!
had the dude at the depot cut the ply there...lol
had the dude at the depot cut the ply there...lol
CF Veteran
Joined: Nov 2008
Posts: 1,021
Likes: 3
From: mass
Year: 1992
Model: Cherokee
Engine: 4.0 high output
Yea it just goes in the receiver. There is also anti tilt thing that clamps on to the hitch bar and receiver to keep it from shifting back and forth. It's ok but I think I'm gonna shim up the hitch bar so it fits tighter. I'm taking welding classes, ill hopefully get it done in class thursday.
CF Veteran
Joined: Jan 2011
Posts: 11,176
Likes: 1
From: Ohio
Year: 1995
Model: Cherokee
Engine: 4.0
Originally Posted by Blackolive
Reattached factory fender flares (with a bit of heat for stretch ) 45* cuts on the front bumper. Feeling happy!
CF Veteran
Joined: Jan 2011
Posts: 11,176
Likes: 1
From: Ohio
Year: 1995
Model: Cherokee
Engine: 4.0
Originally Posted by Blackolive
I can't stand the wait. I put back some $ and washed out my large cooler. Gonna fab up some yank rings for the front while I'm at it. Tomorrow gonna get my rear gears welded up too.
Newbie
Joined: Mar 2012
Posts: 8
Likes: 0
From: Jacksonville NC
Year: 1996
Model: Cherokee
Engine: 97+ 4.0l
Replaced.... Water pump, tstat, coolant sensor, temp sending unit, radiator, took out vacuum thingy on the heater hoses and put a t valve in bottom hose... New coolant and oil change...
