Finish for custom front bumper?
#1
Member
Thread Starter
Join Date: Aug 2011
Location: Capital Region, NY
Posts: 210
Likes: 0
Received 1 Like
on
1 Post
Year: 2000
Model: Cherokee
Engine: 4.0L
Finish for custom front bumper?
hey y'all, I've got a custom front bumper I put on my '00 about 4 years ago down in NC. It was mint condition until, after just one winter of NY's salty roads, this last year it started to develop a coating of rust in about 12 different spots. The original matte black finish is starting to flake off in a few areas and especially at weld points.
What would you fabricators suggest as a finish I could apply to cover. and prevent further rust? I have a big can of rust oleum bed liner in matte black.
What would you fabricators suggest as a finish I could apply to cover. and prevent further rust? I have a big can of rust oleum bed liner in matte black.
#2
Senior Member
Join Date: Mar 2009
Location: Tucson, AZ
Posts: 979
Likes: 0
Received 0 Likes
on
0 Posts
Year: 1991
Model: Cherokee
Engine: 4.0
I would sand it down and clean with alcohol then apply about 2-3 coats of primer. Once primered I would lay down that bed liner or if you want to a real pro job you can fine sand that primer then apply the bed liner. I did about 7 coats of truck liner on mine it only flaked in areas where I hit something with it. A drunk lady rear ended me at a mcdonalds drive thru once and it held up for that surprisingly.
#4
Seasoned Member
Join Date: Jul 2014
Location: Albuquerque
Posts: 389
Likes: 0
Received 0 Likes
on
0 Posts
Year: 2001
Model: Cherokee
Engine: 4.0L Inline 6
I would sand it down and clean with alcohol then apply about 2-3 coats of primer. Once primered I would lay down that bed liner or if you want to a real pro job you can fine sand that primer then apply the bed liner. I did about 7 coats of truck liner on mine it only flaked in areas where I hit something with it. A drunk lady rear ended me at a mcdonalds drive thru once and it held up for that surprisingly.
I use Acetone instead of alcohol. I use Self-Etching Primer and put down at least 3 coats, with a light sanding after each one (200 grit wet/dry, then move up to 300 grit wet/dry), then several 3 - 4 coats of an enamel paint. (I was using Krylon from Walmart but all my trim is yellow, so I spray paint wasn't cutting it for larger, more complicated pieces. I went to Home Depot and had them color match a gallon of their exterior enamel and now I foam brush into the hard to reach corners, and then roll on with a mini-roller, topping with spray paint where the coverage still isn't ideal.)
With ALL painting, the prep is by far the most time consuming. About 80-90% of painting is prep. Spend the time there and it will come out great.
#5
CF Veteran
Join Date: Jul 2013
Location: Monett, MO.
Posts: 7,554
Likes: 0
Received 14 Likes
on
14 Posts
Year: 1999
Model: Cherokee
Engine: 4.0
Where you live all I would do is hit it a little with sandpaper then spray it with Rustoleum as needed. Even a really good powder coat won't hold up in the rust belt nor will your XJ sorry to say.
Rustoleum is all I use on my front tube bumper not because of rust but of all the trees/brush I run over making my own trails. Its easy to touchup looks good and not a PITA like the liners and such.
Rustoleum is all I use on my front tube bumper not because of rust but of all the trees/brush I run over making my own trails. Its easy to touchup looks good and not a PITA like the liners and such.
#6
Senior Member
Join Date: Mar 2009
Location: Tucson, AZ
Posts: 979
Likes: 0
Received 0 Likes
on
0 Posts
Year: 1991
Model: Cherokee
Engine: 4.0
My only complaint on bed liner is the sun eats up the finish and after a few weeks it looks faded black. The upside tho is its cheap and easy to just go over it with a new coat every now and then.
Trending Topics
#8
Junior Member
Join Date: Jan 2015
Location: Sleeping under a Jeep in OZ
Posts: 45
Likes: 0
Received 0 Likes
on
0 Posts
Year: three x 2001's
Model: Cherokee
The Best I can't offer as a solution was I asked a friend that is a corrosion/coatings/paint specialist for a Mobile Conveyer manufacturing company........ When I finish most of my fabrication projects I take it to him, he sandblasts it (removes all rust, paint, greases & oils so don't touch with your bear hands''''''use clean disposable gloves) & either get it powder coated or epoxi-etch prime then 3 light coats of top coat....... I sometimes use a Stone Guard for a different look
#9
Member
Thread Starter
Join Date: Aug 2011
Location: Capital Region, NY
Posts: 210
Likes: 0
Received 1 Like
on
1 Post
Year: 2000
Model: Cherokee
Engine: 4.0L
Lots of great input, thanks all! Realizing this is probably going to be an annual or semi-annual type of job here in the land of eternal winter (okay, 6 months) I may go for the sand and rustoleum approach as needed.
This car is probably on its last couple of years and function has certainly overtaken form...but we'll get as much out of her as I can!
This car is probably on its last couple of years and function has certainly overtaken form...but we'll get as much out of her as I can!
Thread
Thread Starter
Forum
Replies
Last Post
Desertfox1023
Cherokee of the Month
15
09-16-2015 09:14 AM
Buzball
Stock Grand Cherokee Tech. All ZJ/WJ/WK Non-modified/stock questions go here!
3
09-02-2015 05:28 PM
Currently Active Users Viewing This Thread: 1 (0 members and 1 guests)