Homebrew Jeep Mods
Senior Member
Joined: Jul 2010
Posts: 997
Likes: 1
From: Long Island NY
Year: 2000
Model: Cherokee
I used the pines that have the holes down them for the cotter pin, I took 8 washers and welded pairs of two together so it was like 4 thick ones, I welded one of the pairs to the inside of both the pins and the others can slide on the other end. I cut the old bolts off and slid in the new ones, its actually a pretty simple mod I will post up a couple pictures later I can't now being that I'm in English
CF Veteran
Joined: Dec 2009
Posts: 1,396
Likes: 2
Model: Cherokee
Rear bump stop catches. 2"x2"x0.188" sq. tubing, mitered and capped with 12GA sheet and welded on top of the factor u-bolt retainer plates. Aftermarket extended progressive poly bump bolted in the stock location.
32's under stock flares with 4.5" lift. - no rubbing
32's under stock flares with 4.5" lift. - no rubbing
CF Veteran
Joined: Aug 2010
Posts: 8,387
Likes: 1
From: The Florida State University
Year: 2001
Model: Cherokee
Engine: I-6 4.0 L
Got really mad at her today! Noticed some chips all the way down to the steel (before they were just down to the primer) and now i noticed my paint cracking!
Junior Member
Joined: Mar 2011
Posts: 89
Likes: 0
From: South Dakota
Year: 1995
Model: Cherokee
Engine: 4.0 HO
Awesome, Im doing the same when the temp warms up a bit now i know it will look good for sure!
Seasoned Member
Joined: Aug 2010
Posts: 330
Likes: 0
From: Grand Junction, CO
Year: 1999
Model: Cherokee
Engine: 4.0L I-6
To the guys that did the rear disc swap, anyone have a left over proportioning valve from a ZJ? I bought one online and only got the little red piece. Never heard from the guy again. 
Just That Awesome
Joined: Oct 2010
Posts: 1,673
Likes: 0
From: Hannibal, MO
Year: 1993
Model: Grand Cherokee
Engine: 4.0
Newbie
Joined: Feb 2011
Posts: 27
Likes: 0
From: Broken Arrow
Year: 1988
Model: Cherokee
Engine: 4.0
i installed a setup similar to the repeater rig posted on here before, but i did a slight modification, a friend of mine helped me build a DC-DC converter to take the 13.3VDC down to 12.0VDC @ 2.2Amps for the routers via a pair of 7812 power regulators, i'll get some pics after the sun comes out today, and i'll also get some pics of my strobes edit:-> here are the pics as promised
Repeater setup
strobe modules
4.4amp DC/DC Converter (2.2x2)
Repeater setup
strobe modules
4.4amp DC/DC Converter (2.2x2)
Last edited by Jeeper426; Apr 10, 2011 at 08:09 AM.
CF Veteran
Joined: Aug 2010
Posts: 8,387
Likes: 1
From: The Florida State University
Year: 2001
Model: Cherokee
Engine: I-6 4.0 L
i installed a setup similar to the repeater rig posted on here before, but i did a slight modification, a friend of mine helped me build a DC-DC converter to take the 13.3VDC down to 12.0VDC @ 2.2Amps for the routers via a pair of 7812 power regulators, i'll get some pics after the sun comes out today, and i'll also get some pics of my strobes edit:-> here are the pics as promised
Repeater setup
strobe modules
4.4amp DC/DC Converter (2.2x2)
Repeater setup
strobe modules
4.4amp DC/DC Converter (2.2x2)
