Fabrication & builders section. All fabrication posts go here.
XJ/MJ/ZJ/WJ Only projects go here. Questions belong in modified tech.

gas tank skid

Thread Tools
 
Search this Thread
 
Old 03-27-2010, 02:00 PM
  #1  
CF Veteran
Thread Starter
 
phillyxj570's Avatar
 
Join Date: Mar 2010
Location: wilkes barre PA.
Posts: 1,200
Likes: 0
Received 0 Likes on 0 Posts
Year: 96
Model: Cherokee
Engine: 6 cylinder
Default gas tank skid

i have a zj gas tank skid that i am trying to mount onto my xj. the skid lines up with the frame but i dont know how to blot it up. has anybody tried this b4 if so how did you mount it on any help would be greatly appreciated.
Thanks
Old 03-27-2010, 02:02 PM
  #2  
Senior Member
 
halmotors's Avatar
 
Join Date: Oct 2009
Location: Sutton, New Hampshire
Posts: 633
Likes: 0
Received 0 Likes on 0 Posts
Year: 1995
Model: Cherokee
Engine: 4.0L
Default

https://www.cherokeeforum.com/f51/ho...d-97-xj-28676/

Keep in mind this is for a 97+ XJ, so if you have one older than that, you may have to modify it a little.
Old 03-27-2010, 02:11 PM
  #3  
CF Veteran
Thread Starter
 
phillyxj570's Avatar
 
Join Date: Mar 2010
Location: wilkes barre PA.
Posts: 1,200
Likes: 0
Received 0 Likes on 0 Posts
Year: 96
Model: Cherokee
Engine: 6 cylinder
Default

how do i get the nut strips into the frame i took off the bumper and there was no open end to get any thing into the frame
Old 03-27-2010, 02:13 PM
  #4  
Seasoned Member
 
mrmikey32's Avatar
 
Join Date: Dec 2009
Location: Lake in the hills,IL
Posts: 462
Likes: 0
Received 0 Likes on 0 Posts
Year: 2001
Model: Cherokee
Engine: 4.0
Default

oh you can get nuts in to there. its a pain in the ***. its easier to put a bolt, then the nut
Old 03-27-2010, 02:17 PM
  #5  
CF Veteran
Thread Starter
 
phillyxj570's Avatar
 
Join Date: Mar 2010
Location: wilkes barre PA.
Posts: 1,200
Likes: 0
Received 0 Likes on 0 Posts
Year: 96
Model: Cherokee
Engine: 6 cylinder
Default

i was tryin to get it on earlier today i had the skid in place i had to drill new holes in the frame. i bored an existing hole out to get bolts up in the frame but i was having a hard a**time tryin to get the bolt to fall into the new holes.
Old 03-27-2010, 02:23 PM
  #6  
CF Veteran
Thread Starter
 
phillyxj570's Avatar
 
Join Date: Mar 2010
Location: wilkes barre PA.
Posts: 1,200
Likes: 0
Received 0 Likes on 0 Posts
Year: 96
Model: Cherokee
Engine: 6 cylinder
Default

even if i put the bolt in the frame or the nut i have no room to hold one or the other n place to tighten up unless i tack weld it in place
Old 03-27-2010, 02:34 PM
  #7  
Seasoned Member
 
mrmikey32's Avatar
 
Join Date: Dec 2009
Location: Lake in the hills,IL
Posts: 462
Likes: 0
Received 0 Likes on 0 Posts
Year: 2001
Model: Cherokee
Engine: 4.0
Default

then you are doing it wrong... I installed my hitch in under 1 hr, and had no idea what i was doing.

Let me try and find the diy
Old 03-27-2010, 02:38 PM
  #8  
Seasoned Member
 
mrmikey32's Avatar
 
Join Date: Dec 2009
Location: Lake in the hills,IL
Posts: 462
Likes: 0
Received 0 Likes on 0 Posts
Year: 2001
Model: Cherokee
Engine: 4.0
Default

here, check this out

http://www.naxja.org/forum/showthread.php?t=1026081

the bolts where long enough that i could grab them with needle nose, and then tighten the nuts enough. then the lock washers grabbed, and used the impact.

i am super new to jeeps, and never installed a hitch... which is similar to the tank skid. it took me under an hr. i also used jack stands/2x4s to hold it up to the frame
Old 03-27-2010, 02:42 PM
  #9  
Seasoned Member
 
mrmikey32's Avatar
 
Join Date: Dec 2009
Location: Lake in the hills,IL
Posts: 462
Likes: 0
Received 0 Likes on 0 Posts
Year: 2001
Model: Cherokee
Engine: 4.0
Default

also a list of the hardware i used

8 m12x1.75x40mm

and i used matching nuts and washers.

it went bolt in from frame(with washer in between)
then lock washer
then nut
Old 03-27-2010, 03:02 PM
  #10  
CF Veteran
Thread Starter
 
phillyxj570's Avatar
 
Join Date: Mar 2010
Location: wilkes barre PA.
Posts: 1,200
Likes: 0
Received 0 Likes on 0 Posts
Year: 96
Model: Cherokee
Engine: 6 cylinder
Default

where can i get the nut stripes from
Old 03-27-2010, 03:28 PM
  #11  
Seasoned Member
 
mrmikey32's Avatar
 
Join Date: Dec 2009
Location: Lake in the hills,IL
Posts: 462
Likes: 0
Received 0 Likes on 0 Posts
Year: 2001
Model: Cherokee
Engine: 4.0
Default

there is a guy who makes them on naxja, or you can try the search button. i know there have been a lot of threads. Not trying to be a dick, i just dont know if its on here, or naxja.
Related Topics
Thread
Thread Starter
Forum
Replies
Last Post
NVRicochet3006
Stock XJ Cherokee Tech. All XJ Non-modified/stock questions go here
13
09-24-2015 09:43 PM
blueseasons
Cherokee Chat
12
09-21-2015 03:03 PM
jpmarine6786
Stock XJ Cherokee Tech. All XJ Non-modified/stock questions go here
4
09-10-2015 07:46 PM
Chick-N-Picker
Stock XJ Cherokee Tech. All XJ Non-modified/stock questions go here
1
09-06-2015 03:34 PM

Currently Active Users Viewing This Thread: 1 (0 members and 1 guests)
 


Quick Reply: gas tank skid



All times are GMT -5. The time now is 01:57 AM.