Roni's Rogue4x4 Build...finally!
11-02-2017, 08:02 PM
#856
No, I don't lick fish.
Yes they did. I did however find a fix I think. I have to try it out yet though. In Chrome or Firefox you can get an add on from their sites that allows you to view all the photos. I got it but have not tried it out. But on the bright side, with so much to change on the new build, I will be starting a new build thread. Going to have to do something with my user name though, the engine will be on growth hormones
12-10-2017, 05:09 PM
#857
::CF Administrator::
Thread Starter
Ran into another cooling issue. Only happening in traffic at stoplights, newish Mopar stat, HD fan clutch, newish WP, new rad, new electric fan, new hoses,
newish cap...so I decided to test the stat...was bad... never fully opened. Odd for a Mopar stat. So, I grabbed an OEM one from the store, replaced the stat, gasket, and cap, just for ****s and giggles. Also had a known good temp sensor I swapped out just in case. Letting it set up, then we'll see. Haven't driven it in a week. Miss my boo, haha
newish cap...so I decided to test the stat...was bad... never fully opened. Odd for a Mopar stat. So, I grabbed an OEM one from the store, replaced the stat, gasket, and cap, just for ****s and giggles. Also had a known good temp sensor I swapped out just in case. Letting it set up, then we'll see. Haven't driven it in a week. Miss my boo, haha
12-10-2017, 06:02 PM
#858
::CF Administrator::
Thread Starter
Just got back from a lengthy traffic filled road trip. All is well. Sweet.
12-10-2017, 09:13 PM
#859
No, I don't lick fish.
I've always had good luck with STANT thermostats. Any time I've ever run anything else, I've regretted it. That being said, I haven't ever tried the "modern" MOPAR replacements... although their parts have been letting me down as of late.
07-02-2018, 09:13 AM
#860
Senior Member
Join Date: May 2015
Location: Louisville KY
Posts: 736
Likes: 0
Received 4 Likes
on
4 Posts
Year: 01
Model: Cherokee
Roni, just read through this whole thread in the last week or so. *****in build. I’ve got a quick question for ya. I’ve got my rear axle out and fuel tank out to weld in some stiffeners and paint the undercarriage. I’m just wondering what products you used and how they’ve worked out. what stuff did you use to:
paint the axles
spray the undercarriage
clean and prep the metal before primer
thanks a bunch man. Really great info in this thread.
paint the axles
spray the undercarriage
clean and prep the metal before primer
thanks a bunch man. Really great info in this thread.
07-02-2018, 01:17 PM
#861
::CF Administrator::
Thread Starter
Roni, just read through this whole thread in the last week or so. *****in build. I’ve got a quick question for ya. I’ve got my rear axle out and fuel tank out to weld in some stiffeners and paint the undercarriage. I’m just wondering what products you used and how they’ve worked out. what stuff did you use to:
paint the axles
spray the undercarriage
clean and prep the metal before primer
thanks a bunch man. Really great info in this thread.
paint the axles
spray the undercarriage
clean and prep the metal before primer
thanks a bunch man. Really great info in this thread.
Used the same primer and rustoleum rubberized undercoat.
I used a needle scaler for the underbody, followed by an acetone wipe down. Axles were pressure washed with purple power and scrubbed in tough spots, and wiped with acetone before priming and paint.
07-03-2018, 12:31 AM
#866
No, I don't lick fish.
The following users liked this post:
DenimDean (03-23-2020)
