BUILD: My 1987 "Wagoneer" XJ Limited
11-12-2012, 08:36 PM
#31
CF Veteran
Join Date: Aug 2012
Location: Bentonville, AR
Posts: 1,281
Likes: 0
Received 2 Likes
on
2 Posts
Year: 1990
Model: Cherokee
Engine: I6 4.0
That is a beautiful Wagoneer. There is one in decent shape at the junkyard near me. I got the headrest from it. Such an improvement over my 1990 Cherokee Laredo.
11-13-2012, 05:31 PM
#32
Seasoned Member
Thread Starter
11-13-2012, 05:50 PM
#33
Seasoned Member
Thread Starter
11-13-2012, 06:26 PM
#34
CF Veteran
Join Date: Aug 2012
Location: Bentonville, AR
Posts: 1,281
Likes: 0
Received 2 Likes
on
2 Posts
Year: 1990
Model: Cherokee
Engine: I6 4.0
Depends on what parts you want. I can take some pics next time I go there. Might be going tomorrow for some stuff. Just keep in mind it's in Upstate NY so rust is a big killer up here.
11-13-2012, 06:40 PM
#35
Seasoned Member
Thread Starter
Photos in page 2 of this thread...
In order of importance:
1) Driver's side door upper-trim - No dings so that just a polishing would do!
2) One trim end-cap
3) Additional end-caps as spare - But not necessary
4) One or two front door bottom-trim - Optional
I have a source for the windshield-trim... Although I haven't received it as yet... So I don't know it's condition. Fingers crossed!
Thanks!!!
In order of importance:
1) Driver's side door upper-trim - No dings so that just a polishing would do!
2) One trim end-cap
3) Additional end-caps as spare - But not necessary
4) One or two front door bottom-trim - Optional
I have a source for the windshield-trim... Although I haven't received it as yet... So I don't know it's condition. Fingers crossed!
Thanks!!!
11-14-2012, 08:47 AM
#37
Seasoned Member
Thread Starter
Should. There will be a set of clips... One in the trim and the other in the set-hole. Start a bit in from the end and move across and repeat to loosen. If you break the clips... Not a problem. Thanks!
Last edited by Crist Clapper; 11-14-2012 at 09:32 AM.
11-15-2012, 08:30 PM
#38
CF Veteran
Join Date: Aug 2012
Location: Bentonville, AR
Posts: 1,281
Likes: 0
Received 2 Likes
on
2 Posts
Year: 1990
Model: Cherokee
Engine: I6 4.0
No luck at the junkyard. The trim pieces I found where faded and moldy. Even looked at the crush pile but same problem. Good luck with your search and let me know if you need other things.
11-15-2012, 08:46 PM
#39
Seasoned Member
Thread Starter
11-17-2012, 11:13 PM
#41
Seasoned Member
Join Date: Jan 2011
Location: Austin
Posts: 302
Likes: 0
Received 4 Likes
on
3 Posts
Year: 1987
Model: Wagoneer
Engine: 4.0
If/when you take your front doors off, It would be awesome if you could post pics and measurements of the locations of the upper and lower hinges. My door took a hit by a kayak and they now sag... I just can't tell their original position to re-weld them. Thanks!
11-24-2012, 11:58 AM
#44
Seasoned Member
Thread Starter
I found it behind the driver's door upholstered panel. I now can confirm the inside trim color is Tan. At first... The exterior color-code did not cross-reference on a few of the paint-sites. Finally I heard back from one of them... The exterior color is Charcoal Gray Metallic.
11-24-2012, 03:30 PM
#45
CF Veteran
Join Date: Sep 2010
Location: Coos Bay, Or
Posts: 1,024
Likes: 0
Received 0 Likes
on
0 Posts
Year: 1990
Model: Cherokee
Engine: 4.0
Damn mines long gone then. I've had every door panel out of my jeep and never found a build sheet. But that's cool and keep up the good work on the waggy. I'll be watching