North Carolina ~PIC REQUEST~
#93
CF Veteran
Join Date: Aug 2010
Location: Greensboro
Posts: 1,220
Received 0 Likes
on
0 Posts
Year: 1992
Model: Cherokee
Engine: 4.0L
#94
It seems there are a lot of sweet spots to go wheeling down there. I'm going to OBX in a few weeks and wanted to know how far some of you guys are from there in the spots you go wheeling. I'd like to hit some trails down there if their not 2 hours away. I'll be near Corolla if that helps. thanks.
#95
CF Veteran
Join Date: Aug 2010
Location: Greensboro
Posts: 1,220
Received 0 Likes
on
0 Posts
Year: 1992
Model: Cherokee
Engine: 4.0L
Well charlotte is about 5 hours away. Corrolla is up on the northern end of the islands. I'm not too sure where trails are out there
#96
#97
Seasoned Member
Join Date: Oct 2010
Location: Greensboro, NC
Posts: 296
Likes: 0
Received 0 Likes
on
0 Posts
Year: 1997
Model: Cherokee
Engine: 4.0 HO
Figured you folks may appreciate this picture, while moving recently I found this picture in the garage, it is of my first jeep (84 XJ on 33's and my buddys 2000 xj, we were putting the lift kit on his that day. The picture is from roughly... January 2004ish
#100
Member
Join Date: Nov 2010
Location: Lumberton, NC
Posts: 113
Likes: 0
Received 0 Likes
on
0 Posts
Year: 2000
Model: Cherokee
Engine: 4.0
#102
Member
Join Date: Nov 2010
Location: Lumberton, NC
Posts: 113
Likes: 0
Received 0 Likes
on
0 Posts
Year: 2000
Model: Cherokee
Engine: 4.0
I had to get a new front axle because mine was warped and yes I mean warped lol and I got his old high pinion D30 for my 00! So its kinda not stock because its a high pinion...right? lol but, yea he said he had just went to Uwharrie, that's where I dream of going! lol
Last edited by countryboynance; 07-20-2011 at 01:07 AM.
#103
Seasoned Member
Join Date: Oct 2010
Location: Greensboro, NC
Posts: 296
Likes: 0
Received 0 Likes
on
0 Posts
Year: 1997
Model: Cherokee
Engine: 4.0 HO
I had to get a new front axle because mine was warped and yes I mean warped lol and I got his old high pinion D35 for my 00! So its kinda not stock because its a high pinion...right? lol but, yea he said he had just went to Uwharrie, that's where I dream of going! lol
Think you mean a HP D30, its a good axle, better than the low pinion IMO and has the stronger reverse cut gears.
It is still stock though until you regear it, put chromos in, locker, etc...
#104
Member
Join Date: Nov 2010
Location: Lumberton, NC
Posts: 113
Likes: 0
Received 0 Likes
on
0 Posts
Year: 2000
Model: Cherokee
Engine: 4.0
haha yea man my bad..lol fixed that but, yeah I went down a dirt road and was going way to fast and lost control and went in the ditch and it warped the front axle and cracked the T-case..but, while i'm wasting room on here anybody got any 2" or 3" front coil spacers or 3" coils there looking to get rid of?
Edit: Oh, and by the way i'm 16 and still in high school and my job (Lowes Foods) pays min. wage so the only "upgrade" I get is a full tank of gas..haha but, I did make my own CB atenna mount like the ones the guy on here sells and I plan to make a rear tire carrier(similar to the Detours Tailbone so I can keep the stock bumper) or either go all out and make a whole new bumper and front tow points and a roof rack sometime!
Edit: Oh, and by the way i'm 16 and still in high school and my job (Lowes Foods) pays min. wage so the only "upgrade" I get is a full tank of gas..haha but, I did make my own CB atenna mount like the ones the guy on here sells and I plan to make a rear tire carrier(similar to the Detours Tailbone so I can keep the stock bumper) or either go all out and make a whole new bumper and front tow points and a roof rack sometime!
Last edited by countryboynance; 07-20-2011 at 01:14 AM.
#105
Seasoned Member
Join Date: Oct 2010
Location: Greensboro, NC
Posts: 296
Likes: 0
Received 0 Likes
on
0 Posts
Year: 1997
Model: Cherokee
Engine: 4.0 HO
Good stuff bro, youll catch on soon.
Ive got some 2.25 spacers and 3" blocks, technically I gave them to my brother, but he isn't using them so I will see about helping you out.
Check out NC4x4, alot more NC locals.
Ive got some 2.25 spacers and 3" blocks, technically I gave them to my brother, but he isn't using them so I will see about helping you out.
Check out NC4x4, alot more NC locals.