LAS VEGAS XJ GROUP-----> 1st ROLL CALL.
CF Veteran
Joined: Feb 2011
Posts: 1,944
Likes: 0
From: Henderson, NV
Year: 1999
Engine: 4.0L
I did grand Cherokee discs on my jeep. Way better than drums. It was about $450 total because I purchased almost everything new. I only got the backing plates from the junk yard. I might have taken rear calipers too, but I don't remember.
Member
Joined: Apr 2016
Posts: 184
Likes: 0
Model: Cherokee
I won the bid on Ebay 150.00 shipped , I will buy new rotors brakes rubber lines maybe calipers . The only thing I dont know about is the E brake cable ?? HUMMM what to do , what will fit 02 + kj is to long from what I hear
Member
Joined: Apr 2016
Posts: 184
Likes: 0
Model: Cherokee
rotors 2 each new 33.50 shiped
E brake hard ware 13.00
pads 14.00
rubber brake line left 14.00
rubber brake line right 14.00
parking brake shoes 17.56
= 104.10 plus backing plate kit 150.00 = 254.10 and I will still need E brake cables
Senior Member
Joined: Apr 2014
Posts: 840
Likes: 0
From: las vegas, nv
Year: 1991
Model: Cherokee
Engine: I6 H.O, 99 manifold, APN header, neon injectors, cowl intake, screamin demon ignition system
Winch bumper is coming along. Sold my old stinger too. Slowly but surely been putting in work on it. Should be done tomorrow though
Senior Member
Joined: Apr 2014
Posts: 840
Likes: 0
From: las vegas, nv
Year: 1991
Model: Cherokee
Engine: I6 H.O, 99 manifold, APN header, neon injectors, cowl intake, screamin demon ignition system
Half an inch roughly. Should be fine. I know it's not the inch thick stuff that a lot of bumpers have but the fram plates are 3/16 and these are apart of the same plate. Then I welded the c channel up against the plate an gusseted from the back then cut another piece of 3/16 that had the same shape as the shackle mount and butted it up against the c channel then welded it all up. But just like anything time will tell I guess haha
Senior Member
Joined: Apr 2014
Posts: 840
Likes: 0
From: las vegas, nv
Year: 1991
Model: Cherokee
Engine: I6 H.O, 99 manifold, APN header, neon injectors, cowl intake, screamin demon ignition system
Finished up the bumper today an threw some paint on it. I'll get some pics tomorrow after its installed. Ordered some 2 gauge wire for the winch solenoid today but it won't be here till the end of the week sadly. Next up is my tube doors. Can't decide if I'm gonna put her in the big bad jeep show this month.
Junior Member
Joined: Jul 2013
Posts: 62
Likes: 0
From: Centralia Washington
Year: 2000
Model: Cherokee
Engine: 4.0
Well Vegas has been fun but it time to move back to Washington. This weekend I will selling off the last of my salvaged 99 XJ parts. It will include some axles and lots of small parts. I will post a price list tomorrow,
Junior Member
Joined: Jul 2014
Posts: 52
Likes: 0
Junior Member
Joined: Jul 2013
Posts: 62
Likes: 0
From: Centralia Washington
Year: 2000
Model: Cherokee
Engine: 4.0
** NO interior parts left **
Cherokee Sport 5 speed manual
Brake booster & master cylinder: $50
Front brake calipers with lines 2ea: $30
Front Dana 30 used rotors $25
99 Cherokee Rear lift-gate shell & window only $50
Right rear window with rubber seal $30
Stock front driveshaft $40
99 XJ HP Dana 30 stock with 3.07 no axle shafts $100
99 XJ Chrysler 8.25, 3.07 (no drums) needs rebuilt $100
Stock used Track bar $15
Used, steering box $30
ZJ Overhead console $40
Fuel tank (no pump) free
Wiring harnesses, text for price
4.0 liter used flywheel, clutch & pressure plate $50
Reasonable offers will be considered, text, call, or pm @ 360-931-4595
Last edited by klaw13; May 7, 2016 at 11:18 AM.
Member
Joined: Jun 2011
Posts: 123
Likes: 0
From: Brentwood, CA
Year: 1992
Model: Cherokee
Engine: 4.0L I6 MPI "Power Tech HO"
Anyone running anything local in the morning? Tired of running solo. Local as in Henderson boulder city area. If anyone is up for a Burro Wash run I'd totally be down
Last edited by Wingin1t; May 7, 2016 at 02:56 AM.
