transmission control module
#17
Member
Join Date: Feb 2009
Location: Conroe, Tx
Posts: 156
Likes: 0
Received 2 Likes
on
1 Post
Year: 1996 & 2001
Model: Cherokee (XJ)
Engine: 4.0
with tcu unplug you check pins C14 for converter clutch solenoid resistance of 11-15 ohms- pin C15 shift solenoid #2 is 11-15 ohms - pin 16 shift solenoid #1 11-15 ohms
Ps guest I should read post reply be fore posting.
Ps guest I should read post reply be fore posting.
Last edited by McRay; 03-10-2010 at 09:05 AM.
#19
Seasoned Member
Join Date: Dec 2009
Location: Wichita, KS
Posts: 429
Likes: 0
Received 0 Likes
on
0 Posts
Year: 1999
Model: Cherokee
Engine: 4.0l I6
I will tell you this. I removed my dash and forgot to attach the TCM. It would not shift at all between gears. Only way to do it was manually select the gears to get up to third. If you cant even manually shift sometimes? Then it is not the TCM. Guarantee you. If you can always manually go through the gears then there is a high chance that it IS the TCM. But your problem can be either the TCM or even the wiring going to the TCM.
Like I said if sometimes you cant even manually shift (which I read on the first page) Then its not your TCM. I tested it all out for a few days and the TCM only helps it Automatically shift. It has nothing to do with manually going through the gears on the shifter.
Like I said if sometimes you cant even manually shift (which I read on the first page) Then its not your TCM. I tested it all out for a few days and the TCM only helps it Automatically shift. It has nothing to do with manually going through the gears on the shifter.
#20
Seasoned Member
Join Date: Dec 2009
Location: Wichita, KS
Posts: 429
Likes: 0
Received 0 Likes
on
0 Posts
Year: 1999
Model: Cherokee
Engine: 4.0l I6
I must say I think there is still an adjustment you need to do. If you cant manually go through the gears with and without the TCM then its not the TCM. Might be the tranny
#21
Newbie
Thread Starter
Join Date: Jan 2010
Location: conshohocken, pa
Posts: 26
Likes: 0
Received 0 Likes
on
0 Posts
Year: 1995
Model: Cherokee
Engine: 4.0
well, like I said. It's only 2nd gear that it won't go into even manually. There is only the 1-2 selection which it just stays in 1st then when I bump it into 3rd it goes right in most times others I might have to rev it to 3000 rpm and let it off and it will go into then bumped into drive it jumps right into 4th with no problem. and this is with the tcu unplugged. I have a feeling that the one solenoid is just bad. going to test it this afternoon through the plug and see what happens
#22
Newbie
Thread Starter
Join Date: Jan 2010
Location: conshohocken, pa
Posts: 26
Likes: 0
Received 0 Likes
on
0 Posts
Year: 1995
Model: Cherokee
Engine: 4.0
well, I think I have a bad solenoid like I thought. the #2 solenoid. I'm not all that good with electrics but I have my multimeter set on ohms at 200 and I put the negative to d7 and positive to c15 I get 12 as a read out. On c16 I'm getting 317 and on c16 I'm getting 12. So if I'm right then number 2 solenoid is bad. Any ideas where I can get a new one for kinda cheap. Only 2 parts stores seem to be able to get them and they run $280
#23
CF Veteran
You can get all 3 for 182 bucks.
http://www.bulkpart.com/Merchant2/me...roduct_Count=0
and heres a writeup
http://www.naxja.org/forum/showthread.php?t=987463
http://www.bulkpart.com/Merchant2/me...roduct_Count=0
and heres a writeup
http://www.naxja.org/forum/showthread.php?t=987463
#24
Newbie
Thread Starter
Join Date: Jan 2010
Location: conshohocken, pa
Posts: 26
Likes: 0
Received 0 Likes
on
0 Posts
Year: 1995
Model: Cherokee
Engine: 4.0
Now, your sure they fit a 1995 cherokee. When I called the dealer they said that the part I was looking for only fits on a 95 and 96 year. I just want to make sure they are the right ones. And thank you for the info.
#26
Newbie
Thread Starter
Join Date: Jan 2010
Location: conshohocken, pa
Posts: 26
Likes: 0
Received 0 Likes
on
0 Posts
Year: 1995
Model: Cherokee
Engine: 4.0
Thank you every one. This totally fixed my problem. If your not sure if they fit call bulk auto parts and tell them what you have. If they don't they will tell you which ones to get. 96 and older have the throttle cable and the newer don't have it. But the directions that came with mine said all you had to do for the newer ones was to remove the bracket that it comes with it that's held on by a c clip. I would call them and check just in case though
#27
Junior Member
Join Date: Jun 2010
Location: palm bay FL.
Posts: 46
Likes: 0
Received 0 Likes
on
0 Posts
Year: 1996
Model: Cherokee
Engine: 4.0l l6 power tech
Transmission Control Module $$
Hey I just picked up a 96 Cherokee sport for $500 and it does not shift right real sluggish when its in drive but will work if i go 1/2,3 D manually so from reading the forms I think its the (TCM) I priced one at autozone for $266 any one know where i can get one cheaper thank you for your time
#28
Junior Member
Join Date: Dec 2009
Location: South Florida, USA
Posts: 69
Likes: 0
Received 0 Likes
on
0 Posts
Year: 1995
Model: Cherokee
Engine: 4.0
-E
Edit: Oops, just saw this is a months-old thread
Last edited by Eli Lilly; 06-05-2010 at 04:30 PM.
#29
Junior Member
Join Date: Dec 2009
Location: South Florida, USA
Posts: 69
Likes: 0
Received 0 Likes
on
0 Posts
Year: 1995
Model: Cherokee
Engine: 4.0
Hey I just picked up a 96 Cherokee sport for $500 and it does not shift right real sluggish when its in drive but will work if i go 1/2,3 D manually so from reading the forms I think its the (TCM) I priced one at autozone for $266 any one know where i can get one cheaper thank you for your time
-E