STILL NO START
I been messing with this 1990 xj MT for months now and although I've got great info here...still have not been able to solve problem. I have good spark, good fuel pressure at the rail. Jeep tries to start (fires) but won't run. However if i pull the coil wire and crank it for a bit...then plug it back it and start it...it will run for 5-7 seconds....the amount of time it would take to burn up what I cranked in...right? So what I tried to do is give it some throttle during this brief running time and as soon as I touch the throttle it dies. Dies immediately!!! And if I go through the same procedure but hold throttle down a little as I turn it over ...it wont start and run at all. But if I release throttle and crank it,,,it will fire and run for a few seconds.
I have voltage in TPS, although it may need adjustment it still should run right? Seems like jeep is starving for fuel...but I have 40 psi at rail, and when its running for that brief time, still has bout 31 psi.
ANY IDEAS????????? HELP
I have voltage in TPS, although it may need adjustment it still should run right? Seems like jeep is starving for fuel...but I have 40 psi at rail, and when its running for that brief time, still has bout 31 psi.
ANY IDEAS????????? HELP
New CPS, coil, cap, rotor, plugs, fuel filter...did sensor checks...relays..resistor jumped...grounds cleaned up...ect ect.
followed a lot of suggestions from previous threads......nothing. Wonder if the kick out sensor in distributor would cause this???? But it's got something to do with fuel delivery, weather its electrical or not I dont know.
followed a lot of suggestions from previous threads......nothing. Wonder if the kick out sensor in distributor would cause this???? But it's got something to do with fuel delivery, weather its electrical or not I dont know.
Trending Topics
Senior Member
Joined: Aug 2011
Posts: 760
Likes: 6
From: Landers, CA
Year: Several
Model: Cherokee
Engine: 4.0
Sounds to me like wet/fouled plugs.
first - make sure you have the correct plugs in it - no Bosch, no trick stuff like e3's.
Use what the underhood label says to use, not the ones the ex burger flipper guy at the parts house gets a commission on.
Then try the Towruck Driver's Trick.
Pull out the coil wire from the ditributor's center tower.
Hold it 1/4-3/8" away from the tower - use insulated pliers.
Have someone try to start it. It may take 10 - 30 seconds of cranking while you try to find the point as far away from the tower and still have it jump from the wire to the tower. it should be a thin crispy blue spark.
It should eventually sputter and try to start, then start but run terrible. Keep in going, as more cylinders come on line it'll run better and better.
Eventually you'll be able to put the coil wire back in.
let it run a few minutes - give it time to burn off the excess gas puddles in the cylinders.
first - make sure you have the correct plugs in it - no Bosch, no trick stuff like e3's.
Use what the underhood label says to use, not the ones the ex burger flipper guy at the parts house gets a commission on.
Then try the Towruck Driver's Trick.
Pull out the coil wire from the ditributor's center tower.
Hold it 1/4-3/8" away from the tower - use insulated pliers.
Have someone try to start it. It may take 10 - 30 seconds of cranking while you try to find the point as far away from the tower and still have it jump from the wire to the tower. it should be a thin crispy blue spark.
It should eventually sputter and try to start, then start but run terrible. Keep in going, as more cylinders come on line it'll run better and better.
Eventually you'll be able to put the coil wire back in.
let it run a few minutes - give it time to burn off the excess gas puddles in the cylinders.
Last edited by rrich; Sep 28, 2012 at 04:41 PM.
Sounds to me like wet/fouled plugs.
first - make sure you have the correct plugs in it - no Bosch, no trick stuff like e3's.
Use what the underhood label says to use, not the ones the ex burger flipper guy at the parts house gets a commission on.
Then try the Towruck Driver's Trick.
Pull out the coil wire from the ditributor's center tower.
Hold it 1/4-3/8" away from the tower - use insulated pliers.
Have someone try to start it. It may take 10 - 30 seconds of cranking while you try to find the point as far away from the tower and still have it jump from the wire to the tower. it should be a thin crispy blue spark.
It should eventually sputter and try to start, then start but run terrible. Keep in going, as more cylinders come on line it'll run better and better.
Eventually you'll be able to put the coil wire back in.
let it run a few minutes - give it time to burn off the excess gas puddles in the cylinders.
first - make sure you have the correct plugs in it - no Bosch, no trick stuff like e3's.
Use what the underhood label says to use, not the ones the ex burger flipper guy at the parts house gets a commission on.
Then try the Towruck Driver's Trick.
Pull out the coil wire from the ditributor's center tower.
Hold it 1/4-3/8" away from the tower - use insulated pliers.
Have someone try to start it. It may take 10 - 30 seconds of cranking while you try to find the point as far away from the tower and still have it jump from the wire to the tower. it should be a thin crispy blue spark.
It should eventually sputter and try to start, then start but run terrible. Keep in going, as more cylinders come on line it'll run better and better.
Eventually you'll be able to put the coil wire back in.
let it run a few minutes - give it time to burn off the excess gas puddles in the cylinders.
CF Veteran
Joined: Mar 2010
Posts: 47,923
Likes: 38
From: Broward County Fl.
Year: 1989 xj sport 2dr
Model: Cherokee
Engine: 12 hole bosch Injectors
.Have you checked fuel pressure while cranking motor over yet ?
Last edited by freegdr; Sep 28, 2012 at 05:55 PM.
Junior Member
Joined: Jun 2011
Posts: 60
Likes: 0
From: Jackson, MI
Year: 1992 and 1998
Model: Cherokee
Engine: 4.0
This sounds familiar. This spring I had finished rebuilding my 92, and had almost exactly what your talking about. I changed the cranks shaft position sensor, and no difference. Then come to find out, I had the ignition 180 degrees off. Not sure how I did it, but pulled the distributor 3 times and reinserted thinking I had it right each time. 3rd time was the charm. FIred up and ran great.


