cruise control frustration,,,HELP PLZ
#1
Junior Member
Thread Starter
Join Date: Mar 2009
Posts: 30
Likes: 0
Received 0 Likes
on
0 Posts
Year: 1999 limited se
Model: Cherokee
Engine: 6 cyl inline 4.0
cruise control frustration,,,HELP PLZ
PLZ need help goin crazy,,long drive to work each day,,,,cruise control light in dash comes on but wont set,,,,
checked all vac lines n ball under bumper all is good,,,
even switched pcm ecu wit a friend n still doesnt work.
new clock spring new actuator n cable dnt knw what else to do,,,,
plz ny info nybody,,
whn i go over 90 mph the ac vents switch from front to dash vents,,maybe weak vaccum???
checked all vac lines n ball under bumper all is good,,,
even switched pcm ecu wit a friend n still doesnt work.
new clock spring new actuator n cable dnt knw what else to do,,,,
plz ny info nybody,,
whn i go over 90 mph the ac vents switch from front to dash vents,,maybe weak vaccum???
#2
CF Veteran
Join Date: Mar 2010
Location: Broward County Fl.
Posts: 47,923
Likes: 0
Received 22 Likes
on
22 Posts
Year: 1989 xj sport 2dr
Model: Cherokee
Engine: 12 hole bosch Injectors
sounds like a vacuum storage problem vacuum is only created when motors at idle the vacuum ball stores it might need to put new vacuum check vakve in the supply line to the ball it will allow suction to be stored in the ball and not let it out
#5
Junior Member
Thread Starter
Join Date: Mar 2009
Posts: 30
Likes: 0
Received 0 Likes
on
0 Posts
Year: 1999 limited se
Model: Cherokee
Engine: 6 cyl inline 4.0
have u or anyone else heared of an pcm ecu goin bad with only the cruise control???
so u think its a vac problem or elect problem???
should i run to any junk yard pick up a vac ball n start thr ??suggestions plz
so u think its a vac problem or elect problem???
should i run to any junk yard pick up a vac ball n start thr ??suggestions plz
Trending Topics
#8
Junior Member
Thread Starter
Join Date: Mar 2009
Posts: 30
Likes: 0
Received 0 Likes
on
0 Posts
Year: 1999 limited se
Model: Cherokee
Engine: 6 cyl inline 4.0
yes i have,,,n still nthin,,,whn i press the on off button the cruise lights up in dash n thrs a signal sent to the servo tested it wit test lamp,,,but whn i press set or resune accell or coast nthin gets sent to servo,,nt sure if it should or nt or only over 30mph it gets the signal,..cant find nythin,,,ny ideas
#10
Junior Member
Thread Starter
Join Date: Mar 2009
Posts: 30
Likes: 0
Received 0 Likes
on
0 Posts
Year: 1999 limited se
Model: Cherokee
Engine: 6 cyl inline 4.0
no i read on the link u posted that the electrical signal only goes thru the ecm to the servo over 30 mph,,
am nt sure that happens so i tried a friends ecm n his cruise works but mine doesnt even wit his ecm so still cnt find nythin
am nt sure that happens so i tried a friends ecm n his cruise works but mine doesnt even wit his ecm so still cnt find nythin
#11
Junior Member
Thread Starter
Join Date: Mar 2009
Posts: 30
Likes: 0
Received 0 Likes
on
0 Posts
Year: 1999 limited se
Model: Cherokee
Engine: 6 cyl inline 4.0
can the cruise control go bad from pcm ecu???can the pcm ecu be the problem???
and if it is ,,,how can it effect only cruise control
and if it is ,,,how can it effect only cruise control
#13
Junior Member
Thread Starter
Join Date: Mar 2009
Posts: 30
Likes: 0
Received 0 Likes
on
0 Posts
Year: 1999 limited se
Model: Cherokee
Engine: 6 cyl inline 4.0
finally got it ,,,,,,,,,,,,,cruise control on
,,,,had a bad nss and a bad brake lamp switch,,,,
both were workin fine but the continuity between the pins were bad,,,,
tuff frustrating to find it out but finally got it goin
,,,,had a bad nss and a bad brake lamp switch,,,,
both were workin fine but the continuity between the pins were bad,,,,
tuff frustrating to find it out but finally got it goin