What did you do to your Cherokee today?
Seasoned Member
Joined: Jan 2011
Posts: 284
Likes: 0
From: Burlington, VT
Year: 2001
Model: Cherokee
Engine: 4.0L
Dropped it off at the shop and gave them a piece of my mind. They put in a new radiator, called it done, and charged me 300 bucks. However, I'm still losing coolant and there wasn't any leak beforehand. I feel like they just crossed off the first step for a problem and didn't do anything else.
They're running all the tests for free, and if they come up negative, pulling the cylinder head out and taking it to a machine shop to flux it. ****ers.
They're running all the tests for free, and if they come up negative, pulling the cylinder head out and taking it to a machine shop to flux it. ****ers.
Member
Joined: Feb 2011
Posts: 223
Likes: 0
From: Oak Park IL
Year: 2000
Model: Cherokee
Engine: I6
The New bumper arrived today! Incredibly built and it can take a beating! If you need a bumper check out littleleonard0909. He creates some awesome stuff and his prices are freaking fantastic!!!
Seasoned Member
Joined: Mar 2010
Posts: 388
Likes: 0
From: North, Ga
Year: 1995
Model: Grand Cherokee
Engine: 4.0
Started to swap out the passenger side front brake caliper but couldn't finish due to the pain from my broken foot. So my Jeep is sitting in the drive way on a jack stand with a new caliper and pads all I have left is to bleed the brakes and put the wheel back on.
I got to get it running so I can drive it to the salvage yard to go pick up the motor for my celica.
I got to get it running so I can drive it to the salvage yard to go pick up the motor for my celica.
CF Veteran
Joined: Aug 2010
Posts: 1,678
Likes: 0
From: Carlisle, PA
Year: 2000
Model: Cherokee
Engine: Inline 6
got mine today as well! except mines the rear bumper. gotta paint it then its goin on!
Last edited by rtralabama; Feb 22, 2011 at 08:17 PM.
Seasoned Member
Joined: Dec 2010
Posts: 345
Likes: 1
From: So. California
Year: 1991
Model: Cherokee
Engine: 4.0 HO
BTW, Nice looking bumper too!!
Seasoned Member
Joined: Jul 2010
Posts: 400
Likes: 1
From: East Freetown MA
Year: 2000
Model: Cherokee
Engine: 4.0
Started to replace my drivers front hub assembly. Two broken breaker bars and some swearing later, the jeep sits in my driveway with all associated bolts soaked in pb waiting for me to return tomorrow with a brandy new bar and a better attitude.
CF Veteran
Joined: May 2010
Posts: 3,405
Likes: 2
From: Fort Collins, CO
Year: 1996
Engine: 4.0L HO
Fixed my LED dash lights for the third and hopefully final time. I put the stock bulbs back in for the turn signal indicators since the LEDs kept going out and were hard to see in daylight.
I like my blue glowing dash. Will post pics once I do the tcase and trans lever.
I like my blue glowing dash. Will post pics once I do the tcase and trans lever.
CF Veteran
Joined: Jan 2011
Posts: 1,375
Likes: 3
From: Maine
Year: 2000
Model: Cherokee
Engine: 4.0L I6
I trouble shot my ABS system and found a bad wheel speed sensor on the passenger rear. I shopped around for a replacement and most everyone wanted over a $100 for two pieces of wire with a connector on one end and a magnet on the other. What a joke!
Found one on amazon dot com for $52 in case anyone has the same problem. Before you ask "why do I still have ABS on my jeep?", I just bought it and it is all stock. I will lift it and all that good stuff down the road
but for now...
Found one on amazon dot com for $52 in case anyone has the same problem. Before you ask "why do I still have ABS on my jeep?", I just bought it and it is all stock. I will lift it and all that good stuff down the road
but for now...Anyways, I added more coolant, and checked for leaks again.