Jeep Cherokee Forum
DSC01026
DSC01026
0 2010/05/08 10:55:32
WILD BILL
WILD BILL
0 2010/05/08 10:53:20
walkernaxja006
walkernaxja006
0 2010/05/08 10:53:20
DSC01594
DSC01594
0 2010/05/08 10:53:20
DSC01023
DSC01023
0 2010/05/08 10:44:25
snorkel 3
snorkel 3
0 2010/05/08 10:44:25
inside snorkel hole
inside snorkel hole
0 2010/05/08 10:44:25
ATV bag fits nicely ontop of my ladder system.
ATV bag fits nicely ontop of my ladder system.
0 2010/05/08 10:44:25
With stock bumper I received a little body damage coming off a rock, so I built my rear bumper with bats underneath to slide off rocks.
With stock bumper I received a little body damage coming off a rock, so I built my rear bumper with bats underneath to slide off rocks.
0 2010/05/08 10:44:25
Bumper 10
Bumper 10
0 2010/05/08 10:41:54
Bumper 9
Bumper 9
0 2010/05/08 10:41:54
Bumper 8
Bumper 8
0 2010/05/08 10:41:54
Bumper 7
Bumper 7
0 2010/05/08 10:41:54
Bumper 6
Bumper 6
0 2010/05/08 10:41:54
bumper 5
bumper 5
0 2010/05/08 10:41:19
bumper 4
bumper 4
0 2010/05/08 10:41:19
Bumper 3
Bumper 3
0 2010/05/08 10:41:19
Bumper 2
Bumper 2
0 2010/05/08 10:41:19
Bumper 1
Bumper 1
0 2010/05/08 10:41:19
Top Hat Rack Back, thi rack has two mounting tabs, so this is where the 2 studs I welded onto the ladder rest and secures with wing nuts.
Top Hat Rack Back, thi rack has two mounting tabs, so this is where the 2 studs I welded onto the ladder rest and secures with wing nuts.
0 2010/05/08 10:39:13
Top Bolt Up, on my Top Hat rack there are rear bolt holes, so I welded a stud into the ladder and then rested these 2 bolts on top, with the wing nuts I secure them (rubber mounts inbetween). Pull 2 pins on bottom, unscrew to top wing nuts and the ladder pulls right off, less then 1 minute.
Top Bolt Up, on my Top Hat rack there are rear bolt holes, so I welded a stud into the ladder and then rested these 2 bolts on top, with the wing nuts I secure them (rubber mounts inbetween). Pull 2 pins on bottom, unscrew to top wing nuts and the ladder pulls right off, less then 1 minute.
0 2010/05/08 10:37:20
To get the angles on the square tubing I used an old hacksaw and cut until I got the angle I needed, then I just repeated the same amount of cuts on 4 pieces. A little cut at a time. Then I welded the cuts and braced it for strength.
To get the angles on the square tubing I used an old hacksaw and cut until I got the angle I needed, then I just repeated the same amount of cuts on 4 pieces. A little cut at a time. Then I welded the cuts and braced it for strength.
0 2010/05/08 10:37:20
Top 1
Top 1
0 2010/05/08 10:37:20
Side 1
Side 1
1 2010/05/08 10:37:20
Rear Bumper Bracket 1
Rear Bumper Bracket 1
0 2010/05/08 10:37:20
Bumper Bracket, this is where the ladder system sits and connects. Metal placed between my bumper ends and the main section.
Bumper Bracket, this is where the ladder system sits and connects. Metal placed between my bumper ends and the main section.
0 2010/05/08 10:35:39
This slides onto the bumper brackets, and then a quick release hold it into place.
This slides onto the bumper brackets, and then a quick release hold it into place.
0 2010/05/08 10:35:39
Bottom Pin Hook Up with quick release pin. My bumper caps bolt on, so I made a plate to go between (needed my room between bumper and body) that has a hole cut out for this ladder to rest on.
Bottom Pin Hook Up with quick release pin. My bumper caps bolt on, so I made a plate to go between (needed my room between bumper and body) that has a hole cut out for this ladder to rest on.
0 2010/05/08 10:35:39
I thought I needed a brace between the two so I decided to place on there. I'm 240lbs and climb up there all the time. It could be built sturdier, but I'm fine with this size square tube.
I thought I needed a brace between the two so I decided to place on there. I'm 240lbs and climb up there all the time. It could be built sturdier, but I'm fine with this size square tube.
0 2010/05/08 10:35:39
Back 2
Back 2
0 2010/05/08 10:35:39
new grill
new grill
0 2009/06/27 08:10:21
new wheels 2
new wheels 2
0 2009/06/27 08:10:21
new wheels 1
new wheels 1
0 2009/06/27 08:10:21
snorkel 3
snorkel 3
0 2009/06/03 21:27:02
snorkel 2
snorkel 2
0 2009/06/03 21:27:02
snorkel 1
snorkel 1
0 2009/06/03 21:27:02
After the top hat rack install 3" with 30's
After the top hat rack install 3" with 30's
2 2009/04/11 18:57:15
After the top hat rack install 3" with 30's
After the top hat rack install 3" with 30's
0 2009/04/11 18:57:15
After the top hat rack install 3" with 30's
After the top hat rack install 3" with 30's
0 2009/04/11 18:57:15
After the top hat rack install 3" with 30's
After the top hat rack install 3" with 30's
1 2009/04/11 18:57:15