Jeep Cherokee Forum
oops, now i see why the yoke needed changing.
oops, now i see why the yoke needed changing.
0 2011/09/03 17:18:38
almost there
almost there
0 2011/09/03 17:15:34
well, it's broke already...
well, it's broke already...
0 2011/09/03 17:15:34
trying to press it out just bent the mount
trying to press it out just bent the mount
0 2011/09/03 17:15:34
no problem, i don't see any issues
no problem, i don't see any issues
0 2011/09/03 17:15:34
new skids are going to have to wait
new skids are going to have to wait
0 2011/09/03 17:15:34
psteeringold
psteeringold
0 2011/08/28 18:52:03
psteeringnew
psteeringnew
0 2011/08/28 18:52:03
dsteeringold
dsteeringold
0 2011/08/28 18:52:03
dsteeringnew
dsteeringnew
0 2011/08/28 18:52:03
right long arm heim mount is messed up. Crossmember is tweaked too. How would you even bend the mount more than the crossmember? more importantly, how an I going to bend them back?
right long arm heim mount is messed up. Crossmember is tweaked too. How would you even bend the mount more than the crossmember? more importantly, how an I going to bend them back?
0 2011/08/08 13:16:13
rear wells are folded, and the fronts look like they stuffed the tire before removing the fender flares. Already straightened the doors so they close properly. Again - hate the stickers!
rear wells are folded, and the fronts look like they stuffed the tire before removing the fender flares. Already straightened the doors so they close properly. Again - hate the stickers!
1 2011/08/08 13:16:13
exhaust doesn't look right, and will probably need to be re-run. Pulled the rear sway bar out already. Front bushings ont he leaf springs need to be replaced.
exhaust doesn't look right, and will probably need to be re-run. Pulled the rear sway bar out already. Front bushings ont he leaf springs need to be replaced.
0 2011/08/08 13:16:13
that short arm mount on the axle is pinched together completely under the bushing. The haynes manual shows that as a gap, so I pried it apart - will weld a brace in between to keep it open.
that short arm mount on the axle is pinched together completely under the bushing. The haynes manual shows that as a gap, so I pried it apart - will weld a brace in between to keep it open.
0 2011/08/08 13:12:45
leaking rear seal. already have it out and to the shop
leaking rear seal. already have it out and to the shop
0 2011/08/08 13:12:45
what is with the u-bolts on the yoke? that can't be right...
what is with the u-bolts on the yoke? that can't be right...
2 2011/08/08 13:12:45
lots of grinding will be leeded to clean up the old mount points. The long arms push on these now
lots of grinding will be leeded to clean up the old mount points. The long arms push on these now
0 2011/08/08 13:12:45
motor mounts are destryoed - Motor is resting on the oil pan
motor mounts are destryoed - Motor is resting on the oil pan
0 2011/08/08 13:12:45
must remove these stickers!
must remove these stickers!
1 2011/08/08 13:07:10
the brake lines probably need to be replaced
the brake lines probably need to be replaced
0 2011/08/08 13:07:10
could see daylight through that bushing. spliced brake line zip-tied to the breather? nice!
could see daylight through that bushing. spliced brake line zip-tied to the breather? nice!
0 2011/08/08 13:07:10
shock mount is shot as is the bushing
shock mount is shot as is the bushing
0 2011/08/08 13:07:10
front drive shafts is sloppy, getting rebuilt
front drive shafts is sloppy, getting rebuilt
0 2011/08/08 13:07:10