Jeep Cherokee Forum
11.) here's both of them
11.) here's both of them
0 2011/01/30 00:40:38
10.) then i slid the lip of the vent under the hood & laid the L-brackets i made on top of the hood.
10.) then i slid the lip of the vent under the hood & laid the L-brackets i made on top of the hood.
0 2011/01/30 00:40:38
6.) marked out & cut a hole in the back for the vent
6.) marked out & cut a hole in the back for the vent
0 2011/01/30 00:31:13
9.) took off the old vents & used a steel brush on my drill to clean up the bond-o & other stuff the po used to full the gaps
9.) took off the old vents & used a steel brush on my drill to clean up the bond-o & other stuff the po used to full the gaps
0 2011/01/30 00:22:03
8.) then i painted w/ hi-temp bbq black (i don't care too much about the paint right now, but will probably re-paint @ a later point.
8.) then i painted w/ hi-temp bbq black (i don't care too much about the paint right now, but will probably re-paint @ a later point.
0 2011/01/30 00:22:03
7.) riveted in some screen (the screen came from the 8" vent that these were covering). if i were to do this again, i would use some heavier screen, or small expanded aluminum or steel.
7.) riveted in some screen (the screen came from the 8" vent that these were covering). if i were to do this again, i would use some heavier screen, or small expanded aluminum or steel.
0 2011/01/30 00:22:03
5.) slid & riveted the lip up inside the rest of the cover.
5.) slid & riveted the lip up inside the rest of the cover.
0 2011/01/30 00:08:11
4.) took a pair of tin snips & cut the front lip off.....
4.) took a pair of tin snips & cut the front lip off.....
0 2011/01/30 00:08:11
3.) so i took some exterior heater/fan exhaust vents i got for cheap from the local recycle center ($8)
3.) so i took some exterior heater/fan exhaust vents i got for cheap from the local recycle center ($8)
0 2011/01/30 00:08:11
2.) he used interior wall heater registers/vents & no drain pan, so water was dripping right on the distrib. & other electronics. note the driver's side isn't even straight!
2.) he used interior wall heater registers/vents & no drain pan, so water was dripping right on the distrib. & other electronics. note the driver's side isn't even straight!
0 2011/01/30 00:08:11
1.) the po had a good idea w/ hood vents, but........
1.) the po had a good idea w/ hood vents, but........
0 2011/01/30 00:08:11
stock vs. KOR
stock vs. KOR
0 2010/10/28 02:45:19
KOR track bar axle
KOR track bar axle
0 2010/10/28 02:45:19
KOR track bar frame
KOR track bar frame
0 2010/10/28 02:45:19
stock track bar axle
stock track bar axle
0 2010/10/28 02:45:19
stock track bar frame
stock track bar frame
0 2010/10/28 02:45:19
stock speaker vs 6x9
stock speaker vs 6x9
0 2010/10/28 02:28:16
cheap-a$$ cargo rack
cheap-a$$ cargo rack
0 2010/10/28 02:28:16
origins
origins
0 2010/10/28 02:28:16
Lil' Smoky!
Lil' Smoky!
0 2010/10/28 02:28:16