Jeep Cherokee Forum
New sensor vs. old sensor, obviously the new sensor moves much easier.
New sensor vs. old sensor, obviously the new sensor moves much easier.
0 2016/06/22 16:08:58
Old sensor, some carbon build-up. It doesn't move very easily.
Old sensor, some carbon build-up. It doesn't move very easily.
0 2016/06/22 16:08:54
Not that dirty, but I cleaned it anyway with some brake cleaner.
Not that dirty, but I cleaned it anyway with some brake cleaner.
0 2016/06/22 16:08:49
Throttle body removed from Dat Jeep.
Throttle body removed from Dat Jeep.
0 2016/06/22 16:08:44
New 5778 Timken pinion seal and 3 new 5-153X Spicer u joints.
New 5778 Timken pinion seal and 3 new 5-153X Spicer u joints.
0 2016/06/22 15:03:05
Turned out pretty good for only spending less than $20 total.
Turned out pretty good for only spending less than $20 total.
0 2016/06/20 17:12:36
There is plenty enough clearance between the lower handle and my 8-ball shift knob.
There is plenty enough clearance between the lower handle and my 8-ball shift knob.
0 2016/06/20 17:12:32
0 2016/06/20 17:12:28
The screws don't stick out very far on the back side of the center console trim.
The screws don't stick out very far on the back side of the center console trim.
0 2016/06/20 17:12:24
0 2016/06/20 17:12:15
The screws that are included with the handles are M4-.70 x 25mm. They are too long to use in the modification. I bought M4-.70 x 8mm, oval head machine screws.
The screws that are included with the handles are M4-.70 x 25mm. They are too long to use in the modification. I bought M4-.70 x 8mm, oval head machine screws.
0 2016/06/20 17:10:54
0 2016/06/20 17:09:16
Dimensions: Hole Centers/Spacing: 6-5/16" (160mm) Length: 8-11/16" Width: 3/8" Bar Diameter: 3/8" Projection: 1-1/4"
Dimensions: Hole Centers/Spacing: 6-5/16" (160mm) Length: 8-11/16" Width: 3/8" Bar Diameter: 3/8" Projection: 1-1/4"
0 2016/06/20 17:05:49
The screws that come with the handles are M4-.70 x 25mm. That is too long for this modification. I bought some M4-.70 x 8mm, oval head machine screws.
The screws that come with the handles are M4-.70 x 25mm. That is too long for this modification. I bought some M4-.70 x 8mm, oval head machine screws.
0 2016/06/20 17:05:13
Dimensions: Hole Centers/Spacing: 6-5/16" (160mm) Length: 8-11/16" Width: 3/8" Bar Diameter: 3/8" Projection: 1-1/4"
Dimensions: Hole Centers/Spacing: 6-5/16" (160mm) Length: 8-11/16" Width: 3/8" Bar Diameter: 3/8" Projection: 1-1/4"
0 2016/06/20 17:05:01
0 2016/06/20 17:03:21
0 2016/06/20 17:03:18
0 2016/06/20 17:03:14
0 2016/06/20 17:03:10
0 2016/06/20 17:03:07
The screws that come with the handles are M4-.70 x 25mm. That is too long for this modification. I bought some M4-.70 x 8mm, oval head machine screws.
The screws that come with the handles are M4-.70 x 25mm. That is too long for this modification. I bought some M4-.70 x 8mm, oval head machine screws.
0 2016/06/20 17:03:01
Dimensions: Hole Centers/Spacing: 6-5/16" (160mm) Length: 8-11/16" Width: 3/8" Bar Diameter: 3/8" Projection: 1-1/4"
Dimensions: Hole Centers/Spacing: 6-5/16" (160mm) Length: 8-11/16" Width: 3/8" Bar Diameter: 3/8" Projection: 1-1/4"
0 2016/06/20 17:02:51
The screws that come with the handles are M4-.70 x 25mm. That's much too long for this modification. I went and bought some M4-.70 x 8mm machine screws, oval head phillips.
The screws that come with the handles are M4-.70 x 25mm. That's much too long for this modification. I went and bought some M4-.70 x 8mm machine screws, oval head phillips.
0 2016/06/20 16:59:00
0 2016/06/20 16:58:55
There is plenty enough clearance between the lower handle and the 8-ball shift knob.
There is plenty enough clearance between the lower handle and the 8-ball shift knob.
0 2016/06/20 16:58:51
0 2016/06/20 16:58:46
0 2016/06/20 16:58:40
0 2016/06/20 16:58:35
Dimensions: Hole Centers/Spacing: 6-5/16" (160mm) Length: 8-11/16" Width: 3/8" Bar Diameter: 3/8" Projection: 1-1/4"
Dimensions: Hole Centers/Spacing: 6-5/16" (160mm) Length: 8-11/16" Width: 3/8" Bar Diameter: 3/8" Projection: 1-1/4"
0 2016/06/20 16:52:16
0 2016/06/20 16:51:49
0 2016/06/19 13:35:07
0 2016/06/19 13:35:03
0 2016/06/19 13:34:50
Empty cavity left by the driveshaft.
Empty cavity left by the driveshaft.
0 2016/06/19 13:34:44
Both the transfer case and the axle yokes are in excellent condition apart from being oil-caked.
Both the transfer case and the axle yokes are in excellent condition apart from being oil-caked.
0 2016/06/19 13:34:38
Loosened the transfer case end of the axle. This is the end with the double cardigan joint, which I believe is where the noise is coming from.
Loosened the transfer case end of the axle. This is the end with the double cardigan joint, which I believe is where the noise is coming from.
0 2016/06/19 13:34:31
underside of the left hole
underside of the left hole
0 2016/06/19 13:27:58
underside of the right side hole
underside of the right side hole
0 2016/06/19 13:27:51
I found my missing roll of wiring and continued installation of my 20" LED light bar. Used wiring loom and zip ties to secure the wiring along the bumper tubing and behind the front bumper brace.
I found my missing roll of wiring and continued installation of my 20" LED light bar. Used wiring loom and zip ties to secure the wiring along the bumper tubing and behind the front bumper brace.
0 2016/06/18 11:56:07
Night shots coming tonight
Night shots coming tonight
0 2016/06/18 11:56:01