Jeep Cherokee Forum
quick shot, I'll get better ones soon.
quick shot, I'll get better ones soon.
0 2015/11/07 17:29:46
rear brake lines,Capped and not hooked up
rear brake lines,Capped and not hooked up
0 2015/11/24 05:41:36
Instead of marking the cap I took a reference pic
Instead of marking the cap I took a reference pic
0 2015/11/24 05:44:47
0 2015/11/24 05:50:57
0 2015/11/24 05:51:04
0 2015/11/24 05:51:08
0 2015/11/24 05:51:14
0 2015/11/24 05:51:42
0 2015/11/24 05:51:51
starting to look like a decent XJ.
starting to look like a decent XJ.
0 2016/03/11 20:39:53
0 2016/03/11 20:39:54
0 2016/03/11 20:39:54
the roofrack is made of steel pipe and concrete mesh
the roofrack is made of steel pipe and concrete mesh
0 2016/03/11 20:39:55
235/75 15 with procomps all new
235/75 15 with procomps all new
0 2016/03/11 20:39:56
I cut and rivoted daimond plate after cutting out and rustproofing the rust holes.
I cut and rivoted daimond plate after cutting out and rustproofing the rust holes.
0 2016/03/11 20:39:57
did the same to the top rails
did the same to the top rails
0 2016/03/11 20:39:57
the rust was all the way through
the rust was all the way through
0 2016/03/11 20:46:28
back by the leaf mount
back by the leaf mount
0 2016/03/11 20:46:29
pass side floorpan is rusted away
pass side floorpan is rusted away
0 2016/03/11 20:46:30
a bunch of rust flakes in the rails
a bunch of rust flakes in the rails
0 2016/03/11 20:46:31
started cutting it all out
started cutting it all out
0 2016/03/11 20:46:32
both sides cut completely out
both sides cut completely out
0 2016/03/11 20:46:34
I left the tranny tunnel intact
I left the tranny tunnel intact
0 2016/03/11 20:46:34
the only thing left original is the tunnel
the only thing left original is the tunnel
0 2016/03/11 20:46:36
0 2016/03/11 20:46:37
luckily the rails are not rusted
luckily the rails are not rusted
0 2016/03/11 20:46:37
I broke one of the tranny mount bolts, this shows the top of it
I broke one of the tranny mount bolts, this shows the top of it
0 2016/03/11 20:46:38
the tools i used to do the floorpans
the tools i used to do the floorpans
0 2016/03/11 20:46:39
0 2016/03/11 20:46:40
0 2016/03/11 20:46:41
this is the material I used for the floor pans, it's aluminum roofing
this is the material I used for the floor pans, it's aluminum roofing
0 2016/03/11 20:46:42
this stuff was 10$ from a local repurpose store and i could always take this out and weld in proper sheet later.
this stuff was 10$ from a local repurpose store and i could always take this out and weld in proper sheet later.
0 2016/03/11 20:46:43
tin snips and a board for a straight edge/form brake and I'm in business
tin snips and a board for a straight edge/form brake and I'm in business
0 2016/03/11 20:46:45
I cut it all square, bent it all straight and rivoted it in.
I cut it all square, bent it all straight and rivoted it in.
0 2016/03/11 20:46:46