Jeep Cherokee Forum
0 2017/01/07 11:50:30
0 2017/01/07 11:50:37
0 2017/01/07 11:50:46
0 2017/01/07 11:50:55
0 2017/01/07 11:50:59
0 2017/01/07 11:51:03
0 2017/01/07 11:51:11
0 2017/01/07 12:09:07
0 2017/01/07 12:09:15
0 2017/01/07 12:09:18
0 2017/01/07 16:52:52
0 2017/01/07 16:52:58
0 2017/01/07 16:53:01
0 2017/01/07 16:53:05
0 2017/01/07 16:53:08
Inlet and outlet ports on the drivers side of the rear bumper.
Inlet and outlet ports on the drivers side of the rear bumper.
0 2017/01/14 14:01:33
Drain valve on the passenger side of the rear bumper.
Drain valve on the passenger side of the rear bumper.
0 2017/01/14 14:01:42
I used air brake hose line, rated @ 225 PSI for all of my lines. I will be changing these fittings out for 90 degree fittings to relieve some pressure on the lines
I used air brake hose line, rated @ 225 PSI for all of my lines. I will be changing these fittings out for 90 degree fittings to relieve some pressure on the lines
0 2017/01/14 14:01:51
Here is the manifold I made to fit in Dat Jeep. 160 PSI gauge, 150 PSI relief valve, 120 PSI OFF/90 PSI ON pressure switch and regulator/air line dryer.
Here is the manifold I made to fit in Dat Jeep. 160 PSI gauge, 150 PSI relief valve, 120 PSI OFF/90 PSI ON pressure switch and regulator/air line dryer.
0 2017/01/14 14:06:24
Mounted to rear quarter panel plastic
Mounted to rear quarter panel plastic
0 2017/01/14 14:06:30
Hidden quick disconnect line fitting.
Hidden quick disconnect line fitting.
0 2017/01/14 14:06:36
My air system quick disconnect fitting is hidden behind my fuel door next to my fuel cap.
My air system quick disconnect fitting is hidden behind my fuel door next to my fuel cap.
0 2017/01/14 14:06:40
0 2017/01/14 14:06:43
0 2017/01/14 14:06:48
Mounted the compressor to the floor to prevent lines from becoming disconnected during travels and to discourage theft.
Mounted the compressor to the floor to prevent lines from becoming disconnected during travels and to discourage theft.
0 2017/01/14 14:11:32
Cleaned this up a bit.
Cleaned this up a bit.
0 2017/01/14 14:11:39
All wired up, the system utilizes a relay and uses the pressure switch to control when the compressor turns ON/OFF. I also installed a secondary manual ON/OFF switch to prevent the compressor from running when not in use.
All wired up, the system utilizes a relay and uses the pressure switch to control when the compressor turns ON/OFF. I also installed a secondary manual ON/OFF switch to prevent the compressor from running when not in use.
0 2017/01/14 14:11:43
Air lines all run neatly through the vehicles body/plastic paneling with grommets to prevent damage.
Air lines all run neatly through the vehicles body/plastic paneling with grommets to prevent damage.
0 2017/01/14 14:11:48
Simple ON/OFF switch.
Simple ON/OFF switch.
0 2017/01/14 14:11:51
Used my existing rear outlet box for the discharge line.
Used my existing rear outlet box for the discharge line.
0 2017/01/14 14:11:56
0 2017/01/14 14:12:00
0 2017/01/14 14:12:03
0 2017/01/14 14:12:07
2 Minutes 32 Seconds to fill rear bumper tank to 120 PSI @ 21 degrees F. Should get faster when its warmer outside.
2 Minutes 32 Seconds to fill rear bumper tank to 120 PSI @ 21 degrees F. Should get faster when its warmer outside.
0 2017/01/14 14:12:11
Old LCAs had to be cut out, bolts were seized inside the metal sleeve. They had a lot of side-side play in the brackets and the bushings were torn on both ends on both LCAs.
Old LCAs had to be cut out, bolts were seized inside the metal sleeve. They had a lot of side-side play in the brackets and the bushings were torn on both ends on both LCAs.
0 2017/02/11 15:26:06
New LCAs installed.
New LCAs installed.
0 2017/02/11 15:26:14
0 2017/02/11 15:26:21
0 2017/02/11 15:26:25
Starter was acting up on Dat Jeep - bought a replacement from O'rielly's. Got it swapped out in about 15 minutes. The old one kept locking up and refusing to crank, unless I knocked on the starter housing and jumped the leads. New starter cranks over so much faster, it's a substantial difference.
Starter was acting up on Dat Jeep - bought a replacement from O'rielly's. Got it swapped out in about 15 minutes. The old one kept locking up and refusing to crank, unless I knocked on the starter housing and jumped the leads. New starter cranks over so much faster, it's a substantial difference.
0 2017/02/28 17:07:13
0 2017/03/27 15:41:44