Jeep Cherokee Forum
starting to remove the old headliner material
starting to remove the old headliner material
0 2016/01/16 17:01:29
old material removed - now to remove all of the old foam and glue
old material removed - now to remove all of the old foam and glue
0 2016/01/16 17:01:35
I removed some of it with my finger - DAT JEEP
I removed some of it with my finger - DAT JEEP
0 2016/01/16 17:01:40
getting there
getting there
0 2016/01/17 15:59:00
almost done
almost done
0 2016/01/17 15:59:08
there all "clean"
there all "clean"
0 2016/01/17 15:59:17
getting there
getting there
0 2016/01/17 16:00:30
almost done
almost done
0 2016/01/17 16:00:49
there all "clean"
there all "clean"
0 2016/01/17 16:01:09
there all "clean"
there all "clean"
0 2016/01/17 16:01:30
0 2016/01/17 16:02:01
sun visor recovering
sun visor recovering
0 2016/01/19 15:24:07
passenger 1 done (back)
passenger 1 done (back)
0 2016/01/19 15:24:16
passenger (front)
passenger (front)
0 2016/01/19 15:24:21
drivers 1 done (front)
drivers 1 done (front)
0 2016/01/19 15:24:25
drivers (back)
drivers (back)
0 2016/01/19 15:24:30
sun visor recover success
sun visor recover success
0 2016/01/19 15:24:37
sun visors all done
sun visors all done
0 2016/01/19 15:24:42
All laid out and ready to starting spraying glue - I used Super 77
All laid out and ready to starting spraying glue - I used Super 77
0 2016/01/19 16:45:38
Map light cutout
Map light cutout
0 2016/01/19 16:45:46
0 2016/01/19 16:45:51
Speaker holes and rear dome light cutout
Speaker holes and rear dome light cutout
0 2016/01/19 16:45:58
All done - I am going to wait to reinstall this until Spring since I am going to add some sound deadening material to the ceiling.
All done - I am going to wait to reinstall this until Spring since I am going to add some sound deadening material to the ceiling.
0 2016/01/19 16:46:03
I traced it to the passenger rear side compartment rear dome light speaker connector
I traced it to the passenger rear side compartment rear dome light speaker connector
0 2016/01/24 15:40:10
It looks like the wiring got wet and corroded, causing the wires to short against each other. It melted the connectors also.
It looks like the wiring got wet and corroded, causing the wires to short against each other. It melted the connectors also.
0 2016/01/24 15:40:20
Also it melted the rear dome light connector at the light. If anyone out there knows where i could get one or someone has an extra one i would greatly appreciate it. I know I could go to the JY and find one, but I'm lazy and it's cold out.
Also it melted the rear dome light connector at the light. If anyone out there knows where i could get one or someone has an extra one i would greatly appreciate it. I know I could go to the JY and find one, but I'm lazy and it's cold out.
0 2016/01/24 15:40:27
Finally got around to mounting my cooling fans to my aluminum fan shroud.
Finally got around to mounting my cooling fans to my aluminum fan shroud.
0 2016/01/30 08:37:24
Everything laid out. I started out with center punching the mounting locations, then used a 1/8" drill bit to pre-drill the holes and finally used a 1/4" bit to drill the final hole. Mounted the fans using 1/4" bolts, lock washers & nuts.
Everything laid out. I started out with center punching the mounting locations, then used a 1/8" drill bit to pre-drill the holes and finally used a 1/4" bit to drill the final hole. Mounted the fans using 1/4" bolts, lock washers & nuts.
0 2016/01/30 08:37:33
All mounted up. Here's a radiator side view.
All mounted up. Here's a radiator side view.
0 2016/01/30 08:37:39
Engine side view.
Engine side view.
0 2016/01/30 08:37:46
0 2016/01/30 08:37:54
Mounting up my cooling fans to my aluminum fan shroud.
Mounting up my cooling fans to my aluminum fan shroud.
0 2016/01/30 08:46:38
Got the fans laid out and marked all the mounting holes using a center punch. Drilled all the holes twice, once using a 1/8" bit and finally using a 1/4" bit.
Got the fans laid out and marked all the mounting holes using a center punch. Drilled all the holes twice, once using a 1/8" bit and finally using a 1/4" bit.
0 2016/01/30 08:47:37
Laid out the fans and marked all the mounting locations using a center punch.
Laid out the fans and marked all the mounting locations using a center punch.
0 2016/01/30 08:49:07
0 2016/01/30 08:49:54
0 2016/01/30 08:50:05
0 2016/01/30 08:50:10
0 2016/02/01 15:24:54
0 2016/02/01 15:25:01
0 2016/02/01 15:25:08