Jeep Cherokee Forum
0 2018/06/08 20:24:01
0 2021/08/29 19:21:54
0 2018/06/08 20:24:25
0 2021/08/29 19:21:57
0 2021/08/29 19:45:35
0 2018/06/08 20:24:27
Not sure what all these booger welds were about that I had to grind down... they weren't even on a seam.
Not sure what all these booger welds were about that I had to grind down... they weren't even on a seam.
0 2018/06/08 20:24:28
0 2021/08/29 19:45:40
0 2021/08/29 19:45:47
0 2018/06/08 20:24:32
0 2021/08/29 19:45:52
0 2018/06/08 20:24:34
0 2021/08/29 19:45:58
Ran full beads around these... shoulda stitched 'em... don't know what I was thinking.
Ran full beads around these... shoulda stitched 'em... don't know what I was thinking.
0 2018/06/13 17:05:27
0 2021/08/29 19:47:18
0 2021/08/29 19:50:26
0 2018/06/13 17:05:28
This spot has been repaired at least once before. I'll reinforce it now that I have the work piece standing up for access underneath.
This spot has been repaired at least once before. I'll reinforce it now that I have the work piece standing up for access underneath.
0 2018/06/13 17:05:30
0 2021/08/29 19:50:30
0 2021/08/29 19:50:34
Yeah ran a bead all the way around these too.... I'll fix 'em for the guy when they crack though.
Yeah ran a bead all the way around these too.... I'll fix 'em for the guy when they crack though.
0 2018/06/13 17:05:32
0 2021/09/07 21:14:52
Cut out the rusted area at the front of it.
Cut out the rusted area at the front of it.
0 2018/06/13 17:05:33
0 2022/01/14 13:14:28
0 2018/06/13 17:05:35
Cut out a "repair panel" from a 2x4 that I had just sitting around.
Cut out a "repair panel" from a 2x4 that I had just sitting around.
0 2018/06/13 17:05:37
0 2022/01/14 13:14:39
Drilled holes at the end of the cracks I discovered.
Drilled holes at the end of the cracks I discovered.
0 2018/06/13 17:05:39
0 2022/01/14 13:14:50
0 2022/01/14 13:15:00
0 2018/06/13 17:05:41
0 2022/02/01 19:46:22
0 2018/06/13 17:05:42
0 2022/02/02 07:54:13
Stitched the patch piece in.
Stitched the patch piece in.
0 2018/06/13 17:05:44
Forgot how bad the underside of this was. I'm going to end up just cutting out that section of the sheet metal around that blade. I'll weld reinforcements on the back side of those two angle iron pieces I welded too much on, then I'll probably weld in some reinforcement gussets where the gearbox hump is instead of welding more sheet metal that's going to collect moisture and rust away again.
Forgot how bad the underside of this was. I'm going to end up just cutting out that section of the sheet metal around that blade. I'll weld reinforcements on the back side of those two angle iron pieces I welded too much on, then I'll probably weld in some reinforcement gussets where the gearbox hump is instead of welding more sheet metal that's going to collect moisture and rust away again.
0 2018/06/13 17:05:46
0 2022/02/02 07:54:15
Correct state of my garage right now.
Correct state of my garage right now.
0 2018/06/13 17:05:48
0 2022/02/02 07:54:18
0 2022/02/02 07:59:06