Jeep Cherokee Forum
wv 2
wv 2
0 2009/03/24 20:44:21
wv 3
wv 3
0 2009/03/24 20:44:21
wv 4
wv 4
0 2009/03/24 20:44:21
After the ladder set-up was complete I started working on the rear area behind the bumper. It's painted black and cleaned up my wires for the trailer hitch, drilled and mounted that onto the bumper.
After the ladder set-up was complete I started working on the rear area behind the bumper. It's painted black and cleaned up my wires for the trailer hitch, drilled and mounted that onto the bumper.
2 2009/03/24 20:44:21
After installing the rear ladders. 4.5 on 31's.
After installing the rear ladders. 4.5 on 31's.
0 2009/03/24 20:44:21
After 3" lift intall, and bumper install and FAUX Cuda stripes
After 3" lift intall, and bumper install and FAUX Cuda stripes
1 2009/03/24 21:16:33
Sitting stock after I purchased it in Colorado Springs, minus the painted wheels and little cage
Sitting stock after I purchased it in Colorado Springs, minus the painted wheels and little cage
0 2009/03/24 21:16:33
Sitting with the RC 4.5 Kit and 31's.
Sitting with the RC 4.5 Kit and 31's.
0 2009/03/24 21:16:33
Running my old RC lift
Running my old RC lift
0 2009/03/24 21:16:33
wv1
wv1
0 2009/03/24 21:17:55
wv2
wv2
0 2009/03/24 21:17:55
wv3
wv3
0 2009/03/24 21:17:55
WV4
WV4
0 2009/03/24 21:17:55
After the top hat rack install 3" with 30's
After the top hat rack install 3" with 30's
0 2009/04/11 18:57:15
After the top hat rack install 3" with 30's
After the top hat rack install 3" with 30's
1 2009/04/11 18:57:15
After the top hat rack install 3" with 30's
After the top hat rack install 3" with 30's
0 2009/04/11 18:57:15
After the top hat rack install 3" with 30's
After the top hat rack install 3" with 30's
0 2009/04/11 18:57:15
After the top hat rack install 3" with 30's
After the top hat rack install 3" with 30's
2 2009/04/11 18:57:15
snorkel 1
snorkel 1
0 2009/06/03 21:27:02
snorkel 2
snorkel 2
0 2009/06/03 21:27:02
snorkel 3
snorkel 3
0 2009/06/03 21:27:02
new wheels 1
new wheels 1
0 2009/06/27 08:10:21
new wheels 2
new wheels 2
0 2009/06/27 08:10:21
new grill
new grill
0 2009/06/27 08:10:21
Back 2
Back 2
0 2010/05/08 10:35:39
I thought I needed a brace between the two so I decided to place on there. I'm 240lbs and climb up there all the time. It could be built sturdier, but I'm fine with this size square tube.
I thought I needed a brace between the two so I decided to place on there. I'm 240lbs and climb up there all the time. It could be built sturdier, but I'm fine with this size square tube.
0 2010/05/08 10:35:39
Bottom Pin Hook Up with quick release pin. My bumper caps bolt on, so I made a plate to go between (needed my room between bumper and body) that has a hole cut out for this ladder to rest on.
Bottom Pin Hook Up with quick release pin. My bumper caps bolt on, so I made a plate to go between (needed my room between bumper and body) that has a hole cut out for this ladder to rest on.
0 2010/05/08 10:35:39
This slides onto the bumper brackets, and then a quick release hold it into place.
This slides onto the bumper brackets, and then a quick release hold it into place.
0 2010/05/08 10:35:39
Bumper Bracket, this is where the ladder system sits and connects. Metal placed between my bumper ends and the main section.
Bumper Bracket, this is where the ladder system sits and connects. Metal placed between my bumper ends and the main section.
0 2010/05/08 10:35:39
Rear Bumper Bracket 1
Rear Bumper Bracket 1
0 2010/05/08 10:37:20
Side 1
Side 1
1 2010/05/08 10:37:20
Top 1
Top 1
0 2010/05/08 10:37:20
To get the angles on the square tubing I used an old hacksaw and cut until I got the angle I needed, then I just repeated the same amount of cuts on 4 pieces. A little cut at a time. Then I welded the cuts and braced it for strength.
To get the angles on the square tubing I used an old hacksaw and cut until I got the angle I needed, then I just repeated the same amount of cuts on 4 pieces. A little cut at a time. Then I welded the cuts and braced it for strength.
0 2010/05/08 10:37:20
Top Bolt Up, on my Top Hat rack there are rear bolt holes, so I welded a stud into the ladder and then rested these 2 bolts on top, with the wing nuts I secure them (rubber mounts inbetween). Pull 2 pins on bottom, unscrew to top wing nuts and the ladder pulls right off, less then 1 minute.
Top Bolt Up, on my Top Hat rack there are rear bolt holes, so I welded a stud into the ladder and then rested these 2 bolts on top, with the wing nuts I secure them (rubber mounts inbetween). Pull 2 pins on bottom, unscrew to top wing nuts and the ladder pulls right off, less then 1 minute.
0 2010/05/08 10:37:20
Top Hat Rack Back, thi rack has two mounting tabs, so this is where the 2 studs I welded onto the ladder rest and secures with wing nuts.
Top Hat Rack Back, thi rack has two mounting tabs, so this is where the 2 studs I welded onto the ladder rest and secures with wing nuts.
0 2010/05/08 10:39:13
Bumper 1
Bumper 1
0 2010/05/08 10:41:19
Bumper 2
Bumper 2
0 2010/05/08 10:41:19
Bumper 3
Bumper 3
0 2010/05/08 10:41:19
bumper 4
bumper 4
0 2010/05/08 10:41:19
bumper 5
bumper 5
0 2010/05/08 10:41:19