Jeep Cherokee Forum
0 2021/01/27 20:37:33
0 2021/01/27 23:16:53
0 2021/01/27 23:18:19
0 2021/01/28 12:32:52
Installed in tire with winch
Installed in tire with winch
0 2021/01/28 20:55:33
Mock up minus wheel center
Mock up minus wheel center
0 2021/01/28 20:57:05
Machined out to clear valve core
Machined out to clear valve core
0 2021/01/28 20:58:05
I scrounged up tools to do gears myself. And researched alot. Also made a set pf dana 30 set up bears
I scrounged up tools to do gears myself. And researched alot. Also made a set pf dana 30 set up bears
0 2021/01/30 19:33:33
37s look good on the truck. Figured id burn these up on the truck while im gathering wheel fab stuff. I think theyre to big for the jeep i dont want to loose to much of the 4.88 to that much tire. 4.88 33s feels perfect on the trails 35 probly will to
37s look good on the truck. Figured id burn these up on the truck while im gathering wheel fab stuff. I think theyre to big for the jeep i dont want to loose to much of the 4.88 to that much tire. 4.88 33s feels perfect on the trails 35 probly will to
0 2021/01/30 19:45:55
0 2021/01/30 19:49:00
Pvc insert i made to replace the runflats
Pvc insert i made to replace the runflats
0 2021/01/30 19:52:17
Test run winching insert into tire. With tgese wheels i can pack a spare tire no extra wheel needed
Test run winching insert into tire. With tgese wheels i can pack a spare tire no extra wheel needed
0 2021/01/30 19:54:55
From a trail today
From a trail today
0 2021/01/30 19:59:53
0 2021/01/30 20:01:28
0 2021/01/30 20:01:56
Bought it for now. Constant tunning and changing. By the way tires will be from interco probly boggers.
Bought it for now. Constant tunning and changing. By the way tires will be from interco probly boggers.
0 2021/01/30 20:03:16
0 2021/01/30 20:04:47
Heres my ten seal after less than 1000 miles was making lots of grinding noise. It came loose inside housing was spinning with inner shaft. I pulled it, now the other side is doing the same thing. I feel they cost me time and money over stock. Not worth it. In my opinion
Heres my ten seal after less than 1000 miles was making lots of grinding noise. It came loose inside housing was spinning with inner shaft. I pulled it, now the other side is doing the same thing. I feel they cost me time and money over stock. Not worth it. In my opinion
0 2021/02/01 05:52:25
0 2021/02/01 06:02:20
0 2021/02/01 06:03:43
0 2021/02/02 21:51:47
Wheel halves just bolt over the tire sandwiching the insert in the middle
Wheel halves just bolt over the tire sandwiching the insert in the middle
0 2021/02/02 21:52:39
Less than 3" 33x12.5s lots of cutting
Less than 3" 33x12.5s lots of cutting
0 2021/02/10 11:52:26
0 2021/02/10 17:54:46
0 2021/02/10 17:55:31
0 2021/02/10 18:01:41
Went out with a group of capable rigs. Took some runs known as buggy runs. Requires lockers all around. 3rigs broke axles.
Went out with a group of capable rigs. Took some runs known as buggy runs. Requires lockers all around. 3rigs broke axles.
0 2021/02/10 18:02:25
0 2021/02/11 06:25:40
0 2021/02/11 06:26:50
0 2021/02/11 06:27:14
0 2021/02/11 06:28:37
Figured id burn them down on my daily since i dknt really plan or want to run them on the trail. 35" boggers or tsl is my plan Was going to recenter but may now hokd off till i figure what axle are going were. If bigger joint 30 shafts hokd up ill recenter for the 5lug pattern
Figured id burn them down on my daily since i dknt really plan or want to run them on the trail. 35" boggers or tsl is my plan Was going to recenter but may now hokd off till i figure what axle are going were. If bigger joint 30 shafts hokd up ill recenter for the 5lug pattern
0 2021/02/11 10:31:53
0 2021/02/14 23:17:54
0 2021/02/14 23:18:56
0 2021/02/15 16:32:28
14bolt eye candy
14bolt eye candy
0 2021/02/16 16:06:47
0 2021/02/16 16:07:14
0 2021/02/22 22:35:15
0 2021/03/06 11:33:56
0 2021/03/06 11:34:31