Track bar bracket..
#1
Seasoned Member
Thread Starter
Join Date: Sep 2012
Location: Long Island, NY
Posts: 446
Likes: 0
Received 0 Likes
on
0 Posts
Year: 1998
Model: Cherokee
Track bar bracket..
I recently put a 3" rough country lift on my XJ, I also added an RC adj, track bar. When I first installed the lift the coil spring was hitting the track bar bracket so bad.. so i then centered the axle, its wasn't much better. Now I am driving around with my track bar on a stock like setting to where my drive side wheel is sitting out of my fender a little more then my passenger wheel...just so the spring doesn't hit the track bar bracket.
I want to go get an alignment but if they center my axle I'll be rubbing that spot again. What I'd really like is to just replace the bracket with one that sits flush inside the wheel well.
I came across this http://www.rustysoffroad.com/jeep-su...unt-xj-zj.html
but im not sure the end would screw into my RC track bar... help me out here peeps
I want to go get an alignment but if they center my axle I'll be rubbing that spot again. What I'd really like is to just replace the bracket with one that sits flush inside the wheel well.
I came across this http://www.rustysoffroad.com/jeep-su...unt-xj-zj.html
but im not sure the end would screw into my RC track bar... help me out here peeps
#2
Cherokee Forum Vendor
Join Date: Mar 2011
Location: Lynden, WA
Posts: 1,448
Likes: 0
Received 1 Like
on
1 Post
Year: 1998
Model: Cherokee
Engine: 4.0
Pictures of the coil? Sounds like your upper arms are too long or lowers are too short cause there to not be enough caster and the coil plate is tilting forward causing the coil spring to bow forward and hit the bracket.
#3
CF Veteran
Join Date: Jul 2011
Location: Warren, Pa
Posts: 2,164
Likes: 0
Received 1 Like
on
1 Post
Year: 97
Model: Cherokee
Engine: 4.0L
This^^.... Honestly, you should have just gotten the iro track bar. Rc track bars are garbage. I've personally seen two of them bend on jeeps with 31's. Enough bashing RC lol what are your lowers set at?
#4
Seasoned Member
Thread Starter
Join Date: Sep 2012
Location: Long Island, NY
Posts: 446
Likes: 0
Received 0 Likes
on
0 Posts
Year: 1998
Model: Cherokee
I got the RC track bar used locally for cheap. it was in good shape. Im on stock lower control arms and stock uppers. wouldn't longer LCA's push the axle forward, making the problem worse?
Trending Topics
#8
Cherokee Forum Vendor
Join Date: Mar 2011
Location: Lynden, WA
Posts: 1,448
Likes: 0
Received 1 Like
on
1 Post
Year: 1998
Model: Cherokee
Engine: 4.0
Thats a stock track bar bracket. Really strange that you are having rubbing issues. Take it to get it aligned and see what they say. That coil could be bowed out like I suspected earlier but cant tell with the picture angle. Best way is to put the front axle on level jack stands and take off the front tires. Then see how your coils look strait on from the side.
#9
Senior Member
Join Date: Jul 2011
Location: Mt. Vernon Washington
Posts: 798
Likes: 0
Received 0 Likes
on
0 Posts
Year: 1991
Model: Cherokee
Engine: 4.0L Renix and tube header
I think RC coil springs have a larger diameter than the OEM and other after market springs. I had the same issue.
#15
Seasoned Member
Thread Starter
Join Date: Sep 2012
Location: Long Island, NY
Posts: 446
Likes: 0
Received 0 Likes
on
0 Posts
Year: 1998
Model: Cherokee
It is seated properly in the bottom I know that for sure. I'll have to take a look at the top when I get home later