more lift.. o no
#1
Newbie
Thread Starter
Join Date: Mar 2011
Location: buffalo ny
Posts: 12
Likes: 0
Received 0 Likes
on
0 Posts
Year: 1999
Model: Cherokee
Engine: 4.0
more lift.. o no
ok i got a 6.5 inch lift already and 34's on... i want another 2 up front so when i flex i dont rub my steal front bumper..(already ripped a couple side biters off :-( ) so just getr coil spacers ?? or new whole coils..... i think my pinion gear is long enough its like a 5 inch drop i think
#2
Increasing the height is not going to help. You need to install bumpstops to limit your up-travel.
Head over to your favorite sporting goods store and buy 6-8 hockey pucks.
Drill a 1/4 or 3/8" hole through the center of each and a cooresponding hole in the bumpstop pad on both sides of your axle.
Slip 3 or 4 pucks between the coils on both sides of your rig and run a long bolt through the pucks and the hole in the pad. secure with a nut and loc-washer.
Instant homemade bumpstops for $10-$12.
Head over to your favorite sporting goods store and buy 6-8 hockey pucks.
Drill a 1/4 or 3/8" hole through the center of each and a cooresponding hole in the bumpstop pad on both sides of your axle.
Slip 3 or 4 pucks between the coils on both sides of your rig and run a long bolt through the pucks and the hole in the pad. secure with a nut and loc-washer.
Instant homemade bumpstops for $10-$12.
#3
Senior Member
Join Date: Jan 2009
Posts: 545
Likes: 0
Received 1 Like
on
1 Post
Year: 1994
Model: Cherokee
Engine: 4.0L Air Intake and TB Spacer
What is your current set made of? How did you drop the pinion gear? Do you mean pitman arm?
You will need to consider:
Steering angles
trackbar
brakelines
drivelin angles
control arm angels
Coil length
rear leafs/shackle angle
bumpstops
You will need to consider:
Steering angles
trackbar
brakelines
drivelin angles
control arm angels
Coil length
rear leafs/shackle angle
bumpstops
#5
Newbie
Thread Starter
Join Date: Mar 2011
Location: buffalo ny
Posts: 12
Likes: 0
Received 0 Likes
on
0 Posts
Year: 1999
Model: Cherokee
Engine: 4.0
Yes, my bad pitman arm... I got enough brake like I got like a whole extra loop for travel.. I just want my rig to sit a little higher for a little play......and so the tires don't rub when I flex a ton
Trending Topics
#8
Senior Member
Join Date: Dec 2010
Location: Rapid City, SD
Posts: 546
Likes: 0
Received 1 Like
on
1 Post
Model: Cherokee
OMG wow dude. Haha, shut up and listen to these people, if you think you got it all figured out, why are you on here posting then?
ADDING BUMPSTOPS LIMITS YOUR UP TRAVEL, Therefore your tires wont RUB when they are flexing UP INTO THE FENDER.
ADDING BUMPSTOPS LIMITS YOUR UP TRAVEL, Therefore your tires wont RUB when they are flexing UP INTO THE FENDER.
#13
Newbie
Thread Starter
Join Date: Mar 2011
Location: buffalo ny
Posts: 12
Likes: 0
Received 0 Likes
on
0 Posts
Year: 1999
Model: Cherokee
Engine: 4.0
I did cut out my fenders I ordered. Bushwhackers.... its just seemed to me that my tires I bought are a little big with the current lift on there the top of the tire to top of inside the fender is like 7 inches...... not my concern its the left in right side of fender when I turn........and have extreme flex... just wanted to raise it a inch or two to clear the sides up....
#15
Newbie
Thread Starter
Join Date: Mar 2011
Location: buffalo ny
Posts: 12
Likes: 0
Received 0 Likes
on
0 Posts
Year: 1999
Model: Cherokee
Engine: 4.0
There was alot of confusing directions in that....... but yes no sway bars equals alot of flex and through this whole thread I just wanted to lift my rig a little higher on top of my lift but I bought 3 inch blocks ( they are on my old jeep) now but im taking them off and I bought 3 inch coil spacers for 50 bucks lol call me dumb but it was a cheap fix for my problem I thought ill take a pic