Online store recommendation
I need some OEM stock engine mounts for my '99, anyone have a suggestion on where to find them online at a good price? I have brown dogs currently but the vibrations are a bit much for me with the truck being a DD.
Thanks for any suggestions. :cheers: |
Advance Auto
|
I thought they were only Duralast?
|
Duralast is good stuff
|
I read a few times that OEM from Mopar/Chrysler was the only way to go..?
|
Ummm no.
|
Give ya $10 bucks shipped for the brown dog mounts.
|
I'll give you $20
|
$55 kthxbye
Might give Duralast a shot. |
The duralast will work fine. I recommend if you havent look already to check your tranny mount as well. If your engine mounts are wore out, your tranny mount is usually wore out as well.
|
^ this....major difference with all new mounts....i was chasin vibes for a while IE tcase drop rear shims new joints etc..replaced all the mounts vibes got a little better...pulled out t case drop and shims and viola no vibes...nice and SMOOTH.. New mounts are well worth the time and $$ even if you dont have vibes...just smooths everything out :) then again I am old and cant stand even the slightest vibe or rattle
my two cents Cameron |
If you haven't ordered them try like rockauto.com or some of our vendors on here.
|
Originally Posted by ck1
(Post 2210006)
^ this....major difference with all new mounts....i was chasin vibes for a while IE tcase drop rear shims new joints etc..replaced all the mounts vibes got a little better...pulled out t case drop and shims and viola no vibes...nice and SMOOTH.. New mounts are well worth the time and $$ even if you dont have vibes...just smooths everything out :) then again I am old and cant stand even the slightest vibe or rattle
my two cents Cameron |
No pics but the best way to make sure just drop your skid plate/x member and look at your mount. You should have a good 2+ inches of rubber between the mount. Get a good pry bar up there and see if you can move the trans a lot. Anything cracked,squished,sagged or broken in half replace it. The 4.0 is a very torquey motor thus hard on all mounts. This is compounded if you are in low range a lot.
Cameron |
Advance Auto has Anchor motor mounts never had a problem with them, plus they price match if you find it cheaper anywhere.... btw Autozone=Duralast parts
|
Trans mount has been done, still vibrating too much for my liking. Hard shift every once in a while too.
Is it Anchor>Duralast? |
I would get the Anchor one over the Duralast one, I work at Advance Auto and I haven't seen a defective Anchor mount come back in my store ever soo
|
Originally Posted by still_alive
(Post 2213075)
I would get the Anchor one over the Duralast one, I work at Advance Auto and I haven't seen a defective Anchor mount come back in my store ever soo
Originally Posted by CrawlinPepper
(Post 2213069)
Trans mount has been done, still vibrating too much for my liking. Hard shift every once in a while too.
|
I still say duralast
|
I say go to Brown Dog and order the rubber bushings and dump the prothane.
If not, any OEM motor mounts will work fine. I'd try rockauto.com as they are usually the cheapest for any OEM part. On another note, if you're dead set on getting rid of your Brown Dogs, I'd be very interested at that price |
4x4 morris jeep center
|
Originally Posted by 1996sportXJ
(Post 2213447)
I say go to Brown Dog and order the rubber bushings and dump the prothane.
If not, any OEM motor mounts will work fine. I'd try rockauto.com as they are usually the cheapest for any OEM part. On another note, if you're dead set on getting rid of your Brown Dogs, I'd be very interested at that price |
Originally Posted by ck1
(Post 2212688)
No pics but the best way to make sure just drop your skid plate/x member and look at your mount. You should have a good 2+ inches of rubber between the mount. Get a good pry bar up there and see if you can move the trans a lot. Anything cracked,squished,sagged or broken in half replace it. The 4.0 is a very torquey motor thus hard on all mounts. This is compounded if you are in low range a lot.
Cameron |
All times are GMT -5. The time now is 05:29 PM. |
© 2024 MH Sub I, LLC dba Internet Brands