Fault Codes...
02-02-2011, 12:02 AM
#1
Member
Thread Starter
Join Date: Nov 2010
Location: Lakewood, CO
Posts: 101
Likes: 0
Received 0 Likes
on
0 Posts
Year: 1995
Model: Cherokee
Engine: 4.0
Fault Codes...
I found these codes after a few hours of looking and I just thought they might be of use to someone else also...
Diagnostic Trouble Codes
Jeeps equipped with a Chrysler computer ('91 and later models) and fuel injection have a "fault code" feature in the engine controller. This allows the engine controller to detect certain "faults" in the system. The codes indicate the result of a failure, but do not identify the failed component directly. The codes are displayed by the CHECK ENGINE light flashing a sequence of two-digit codes. Diagnostic Trouble Codes
To display the codes, start with the ignition off. Within five seconds, switch the key on then off 3 times, and on the third time, leave the key in the on position. (On is not start!) Watch the CHECK ENGINE light, it will then flash the codes. Count the flashes: each code is a two digit code, so a (for example) 33 would be FLASH FLASH FLASH <pause> FLASH FLASH FLASH <long pause> It will never flash more than 9 times, so watch for pauses. 55 is end of codes, 33 is normal if you don't have air conditioning. Please note that some codes are NOT included below, this is not a complete listing, but it IS very close to complete.
Unfortunately, this trick won't work for 1998 and later (OBD-II era) Jeeps. The information returned by OBD-II is more complex, and requires a code scanner ($100-300) to retrieve.
These codes were taken from the '95 XJ/ YJ factory service manual.
Code
Description
11*
No crank reference signal detected during engine cranking.
12*
Direct battery input to PCM was disconnected within the last 50 key-on cycles.
13**
No difference recognized between the engine MAP reading and the barometric (atmosphereic) pressure reading at start-up
14**
MAP sensor input below minimum acceptable voltage.
or
MAP sensor input above maximum acceptable voltage.
15**
No vehicle distance (speed) sensor signal detected during road load conditions.
17*
Engine coolant temperature remains below normal operating temperatures during vehicle travel (thermostat).
21**
Neither rich nor lean condition detected from the oxygen sensor input.
or
Oxygen sensor input voltage maintained above the normal operating range.
22**
Engine coolant temperature sensor input above maximum acceptable voltage.
or
Engine coolant temperature sensor input below minimum acceptable voltage.
23**
Intake manifold air temperature sensor input above maximum acceptable voltage.
or
Intake manifold air temperature sensor input below minimum acceptable voltage.
24**
Throttle position sensor input above maximum acceptable voltage.
or
Throttle position sensor input below minimum acceptable voltage.
25**
A shorted condition detected in one or more of the idle air control motor circuits.
27*
Injector #1 output driver does not respond properly to the control signal.
or
Injector #2 output driver does not respond properly to the control signal.
or
Injector #3 output driver does not respond properly to the control signal.
or
Injector #4 output driver does not respond properly to the control signal.
or
Injector #5 output driver does not respond properly to the control signal.
or
Injector #6 output driver does not respond properly to the control signal.
33*
An open or shorted condition detected in the A/C clutch relay circuit.
34*
An open or shorted condition detected in the speed control vacuum or vent solenoid circuits.
or
Speed control switch input below the minimum acceptable voltage.
or
Speed control switch input above the maximum acceptable voltage.
35*
An open or shorted condition detected in the radiator fan relay circuit.
41*
An open or shorted condition detected in the generator field control circuit.
42*
An open or shorted condition detected in the auto shutdown relay circuit.
44*
An open or shorted condition exists in the engine coolant temperature sensor circuit or a problem exists in the PCM's battery temperature voltage circuit.
46**
Battery voltage sense input above target charging voltage during engine operation.
47**
Battery voltage sense input below target charging voltage during engine operation. Also, no significant change detected in battery voltage during active test of generator output.
51**
Oxygen sensor signal input indicates lean air/fuel ratio condition during engine operation.
52**
Oxygen sensor signal input indicates rich air/fuel ratio condition during engine operation.
53*
PCM internal fault condition detected.
54*
No fuel sync (camshaft signal) detected during engine cranking.
55*
Completion of diagnostic trouble code display on the malfunction indicator lamp (check engine lamp).
62*
Unsuccessful attempt to update SRI (service reminder indicator) miles in the PCM EEPROM.
63*
Unsuccessful attempt to write to an EEPROM location by the PCM.
* - Check engine lamp will not illuminate at all times if this code was recorded. Cycle ignition key as described and observe code flashed by check engine lamp.Description
11*
No crank reference signal detected during engine cranking.
12*
Direct battery input to PCM was disconnected within the last 50 key-on cycles.
13**
No difference recognized between the engine MAP reading and the barometric (atmosphereic) pressure reading at start-up
14**
MAP sensor input below minimum acceptable voltage.
or
MAP sensor input above maximum acceptable voltage.
15**
No vehicle distance (speed) sensor signal detected during road load conditions.
17*
Engine coolant temperature remains below normal operating temperatures during vehicle travel (thermostat).
21**
Neither rich nor lean condition detected from the oxygen sensor input.
or
Oxygen sensor input voltage maintained above the normal operating range.
22**
Engine coolant temperature sensor input above maximum acceptable voltage.
or
Engine coolant temperature sensor input below minimum acceptable voltage.
23**
Intake manifold air temperature sensor input above maximum acceptable voltage.
or
Intake manifold air temperature sensor input below minimum acceptable voltage.
24**
Throttle position sensor input above maximum acceptable voltage.
or
Throttle position sensor input below minimum acceptable voltage.
25**
A shorted condition detected in one or more of the idle air control motor circuits.
27*
Injector #1 output driver does not respond properly to the control signal.
or
Injector #2 output driver does not respond properly to the control signal.
or
Injector #3 output driver does not respond properly to the control signal.
or
Injector #4 output driver does not respond properly to the control signal.
or
Injector #5 output driver does not respond properly to the control signal.
or
Injector #6 output driver does not respond properly to the control signal.
33*
An open or shorted condition detected in the A/C clutch relay circuit.
34*
An open or shorted condition detected in the speed control vacuum or vent solenoid circuits.
or
Speed control switch input below the minimum acceptable voltage.
or
Speed control switch input above the maximum acceptable voltage.
35*
An open or shorted condition detected in the radiator fan relay circuit.
41*
An open or shorted condition detected in the generator field control circuit.
42*
An open or shorted condition detected in the auto shutdown relay circuit.
44*
An open or shorted condition exists in the engine coolant temperature sensor circuit or a problem exists in the PCM's battery temperature voltage circuit.
46**
Battery voltage sense input above target charging voltage during engine operation.
47**
Battery voltage sense input below target charging voltage during engine operation. Also, no significant change detected in battery voltage during active test of generator output.
51**
Oxygen sensor signal input indicates lean air/fuel ratio condition during engine operation.
52**
Oxygen sensor signal input indicates rich air/fuel ratio condition during engine operation.
53*
PCM internal fault condition detected.
54*
No fuel sync (camshaft signal) detected during engine cranking.
55*
Completion of diagnostic trouble code display on the malfunction indicator lamp (check engine lamp).
62*
Unsuccessful attempt to update SRI (service reminder indicator) miles in the PCM EEPROM.
63*
Unsuccessful attempt to write to an EEPROM location by the PCM.
** - Check engine lamp will illuminate during engine operation if this code was recorded.
PCM = Power train Control Module (the engine computer)
MAP = Manifold Absolute Pressure (the sensor that measures how hard the engine is sucking air through the intake manifold
EEPROM = Electrically Erasable Programmable Read Only Memory (a type of computer chip used inside the PCM)
12-13-2014, 07:54 AM
#2
Newbie
Join Date: Apr 2013
Location: Kansas City,Missouri
Posts: 1
Likes: 0
Received 0 Likes
on
0 Posts
Year: 1995
Model: Grand Cherokee
Engine: 5.2L
fault codes
I found these codes after a few hours of looking and I just thought they might be of use to someone else also...
Diagnostic Trouble Codes
Jeeps equipped with a Chrysler computer ('91 and later models) and fuel injection have a "fault code" feature in the engine controller. This allows the engine controller to detect certain "faults" in the system. The codes indicate the result of a failure, but do not identify the failed component directly. The codes are displayed by the CHECK ENGINE light flashing a sequence of two-digit codes. Diagnostic Trouble Codes
To display the codes, start with the ignition off. Within five seconds, switch the key on then off 3 times, and on the third time, leave the key in the on position. (On is not start!) Watch the CHECK ENGINE light, it will then flash the codes. Count the flashes: each code is a two digit code, so a (for example) 33 would be FLASH FLASH FLASH <pause> FLASH FLASH FLASH <long pause> It will never flash more than 9 times, so watch for pauses. 55 is end of codes, 33 is normal if you don't have air conditioning. Please note that some codes are NOT included below, this is not a complete listing, but it IS very close to complete.
Unfortunately, this trick won't work for 1998 and later (OBD-II era) Jeeps. The information returned by OBD-II is more complex, and requires a code scanner ($100-300) to retrieve.
These codes were taken from the '95 XJ/ YJ factory service manual.
Code
Description
11*
No crank reference signal detected during engine cranking.
12*
Direct battery input to PCM was disconnected within the last 50 key-on cycles.
13**
No difference recognized between the engine MAP reading and the barometric (atmosphereic) pressure reading at start-up
14**
MAP sensor input below minimum acceptable voltage.
or
MAP sensor input above maximum acceptable voltage.
15**
No vehicle distance (speed) sensor signal detected during road load conditions.
17*
Engine coolant temperature remains below normal operating temperatures during vehicle travel (thermostat).
21**
Neither rich nor lean condition detected from the oxygen sensor input.
or
Oxygen sensor input voltage maintained above the normal operating range.
22**
Engine coolant temperature sensor input above maximum acceptable voltage.
or
Engine coolant temperature sensor input below minimum acceptable voltage.
23**
Intake manifold air temperature sensor input above maximum acceptable voltage.
or
Intake manifold air temperature sensor input below minimum acceptable voltage.
24**
Throttle position sensor input above maximum acceptable voltage.
or
Throttle position sensor input below minimum acceptable voltage.
25**
A shorted condition detected in one or more of the idle air control motor circuits.
27*
Injector #1 output driver does not respond properly to the control signal.
or
Injector #2 output driver does not respond properly to the control signal.
or
Injector #3 output driver does not respond properly to the control signal.
or
Injector #4 output driver does not respond properly to the control signal.
or
Injector #5 output driver does not respond properly to the control signal.
or
Injector #6 output driver does not respond properly to the control signal.
33*
An open or shorted condition detected in the A/C clutch relay circuit.
34*
An open or shorted condition detected in the speed control vacuum or vent solenoid circuits.
or
Speed control switch input below the minimum acceptable voltage.
or
Speed control switch input above the maximum acceptable voltage.
35*
An open or shorted condition detected in the radiator fan relay circuit.
41*
An open or shorted condition detected in the generator field control circuit.
42*
An open or shorted condition detected in the auto shutdown relay circuit.
44*
An open or shorted condition exists in the engine coolant temperature sensor circuit or a problem exists in the PCM's battery temperature voltage circuit.
46**
Battery voltage sense input above target charging voltage during engine operation.
47**
Battery voltage sense input below target charging voltage during engine operation. Also, no significant change detected in battery voltage during active test of generator output.
51**
Oxygen sensor signal input indicates lean air/fuel ratio condition during engine operation.
52**
Oxygen sensor signal input indicates rich air/fuel ratio condition during engine operation.
53*
PCM internal fault condition detected.
54*
No fuel sync (camshaft signal) detected during engine cranking.
55*
Completion of diagnostic trouble code display on the malfunction indicator lamp (check engine lamp).
62*
Unsuccessful attempt to update SRI (service reminder indicator) miles in the PCM EEPROM.
63*
Unsuccessful attempt to write to an EEPROM location by the PCM.
* - Check engine lamp will not illuminate at all times if this code was recorded. Cycle ignition key as described and observe code flashed by check engine lamp.Description
11*
No crank reference signal detected during engine cranking.
12*
Direct battery input to PCM was disconnected within the last 50 key-on cycles.
13**
No difference recognized between the engine MAP reading and the barometric (atmosphereic) pressure reading at start-up
14**
MAP sensor input below minimum acceptable voltage.
or
MAP sensor input above maximum acceptable voltage.
15**
No vehicle distance (speed) sensor signal detected during road load conditions.
17*
Engine coolant temperature remains below normal operating temperatures during vehicle travel (thermostat).
21**
Neither rich nor lean condition detected from the oxygen sensor input.
or
Oxygen sensor input voltage maintained above the normal operating range.
22**
Engine coolant temperature sensor input above maximum acceptable voltage.
or
Engine coolant temperature sensor input below minimum acceptable voltage.
23**
Intake manifold air temperature sensor input above maximum acceptable voltage.
or
Intake manifold air temperature sensor input below minimum acceptable voltage.
24**
Throttle position sensor input above maximum acceptable voltage.
or
Throttle position sensor input below minimum acceptable voltage.
25**
A shorted condition detected in one or more of the idle air control motor circuits.
27*
Injector #1 output driver does not respond properly to the control signal.
or
Injector #2 output driver does not respond properly to the control signal.
or
Injector #3 output driver does not respond properly to the control signal.
or
Injector #4 output driver does not respond properly to the control signal.
or
Injector #5 output driver does not respond properly to the control signal.
or
Injector #6 output driver does not respond properly to the control signal.
33*
An open or shorted condition detected in the A/C clutch relay circuit.
34*
An open or shorted condition detected in the speed control vacuum or vent solenoid circuits.
or
Speed control switch input below the minimum acceptable voltage.
or
Speed control switch input above the maximum acceptable voltage.
35*
An open or shorted condition detected in the radiator fan relay circuit.
41*
An open or shorted condition detected in the generator field control circuit.
42*
An open or shorted condition detected in the auto shutdown relay circuit.
44*
An open or shorted condition exists in the engine coolant temperature sensor circuit or a problem exists in the PCM's battery temperature voltage circuit.
46**
Battery voltage sense input above target charging voltage during engine operation.
47**
Battery voltage sense input below target charging voltage during engine operation. Also, no significant change detected in battery voltage during active test of generator output.
51**
Oxygen sensor signal input indicates lean air/fuel ratio condition during engine operation.
52**
Oxygen sensor signal input indicates rich air/fuel ratio condition during engine operation.
53*
PCM internal fault condition detected.
54*
No fuel sync (camshaft signal) detected during engine cranking.
55*
Completion of diagnostic trouble code display on the malfunction indicator lamp (check engine lamp).
62*
Unsuccessful attempt to update SRI (service reminder indicator) miles in the PCM EEPROM.
63*
Unsuccessful attempt to write to an EEPROM location by the PCM.
** - Check engine lamp will illuminate during engine operation if this code was recorded.
PCM = Power train Control Module (the engine computer)
MAP = Manifold Absolute Pressure (the sensor that measures how hard the engine is sucking air through the intake manifold
EEPROM = Electrically Erasable Programmable Read Only Memory (a type of computer chip used inside the PCM)
09-28-2015, 08:42 AM
#4
Newbie
Join Date: Sep 2015
Posts: 1
Likes: 0
Received 0 Likes
on
0 Posts
Model: Cherokee
Trouble reading flashes
My 95 cherokee is having some serious problems at 75k miles, yes that's right. My code is flashing 3 times and then flashes another 9 times without a noticeable pause. There might be a short pause between the 9 but there are only two pauses right. Possible readings are 3-2-7; 3-9
Basically I have lost almost all acceleration either not getting all pistons to fire or my transmission is messed up or it could be a terrible combo of both.
Basically I have lost almost all acceleration either not getting all pistons to fire or my transmission is messed up or it could be a terrible combo of both.
Last edited by Mshrake93; 09-28-2015 at 08:45 AM.
Thread
Thread Starter
Forum
Replies
Last Post
BlueXJ
Stock XJ Cherokee Tech. All XJ Non-modified/stock questions go here
75
01-09-2024 02:54 PM
4WD4EVER
Modified XJ Cherokee Tech
28
07-28-2023 07:12 PM
jhc7399
Stock XJ Cherokee Tech. All XJ Non-modified/stock questions go here
19
09-24-2016 03:51 PM
Kathy Zirkle
Cherokee Chat
7
09-27-2015 08:38 PM
ydduba
Stock Grand Cherokee Tech. All ZJ/WJ/WK Non-modified/stock questions go here!
8
08-26-2015 04:26 AM
Currently Active Users Viewing This Thread: 1 (0 members and 1 guests)