carderzj

Hey, guys. I bought a '93 ZJ with a 5.2 a month ago. It runs okay, will get my back and forth to work. However, when accelerating from a stop or trying to speed up the jeep starts cutting out and pops through the tailpipe until you get up to speed then acts fine until it swithes into overdrive. Then it runs rough and I starts vibrating. This will continue until you give it gas and it drops out of overdrive, where it run fine. That is, until it shifts into overdrive again.
When I checked the trouble codes I got: 33, 23, 8 and 55. I got these codes three times in a row so I believe I wrote them down correctly.
I've replaced the cap, rotor, plugs, wires and fuel filter. Any help would be greatly appreciated!

xHATCHx

Found this on another site someone may have to confirm the list. Hope it helps


Might help you to search as its in the FAQ.. But here:

To display codes cycle the ingition key On-Off-On-Off-On within three seconds. Count the number of flashes, first digit, pause then second digit will be displayed in a series of flashes. (2 flashes, pause, 1 flash = 21)

11 - No Crank Reference Signal At PCM (Crankshaft Position Sensor)
12 - Battery Disconnected Within last 50 Key-on cycles
13 - No Change In MAP Sensor
14 - MAP Voltage Too Low Or Too High
15 - No Vehicle Speed Sensor Signal
17 - Engine Is Cold Too Long
21 - O2 Sensor Signal At Center Or Signal Shorted To Voltage
22 - ECT Sensor Voltage Too Low Or Too High (ECT = Engine Coolant Sensor)
23 - Charge Air Temperature Sensor Voltage Too High Or Low (Intake Air Temp Sensor)
24 - Throttle Position Sensor Voltage Too High Or Too Low
25 - Idle Air Control Motor Circuit Shorted
27 - Injector Control Circuit Signal Not Responding Correctly.
31 - EVAP Purge Solenoid Circuit Open Or Shorted
32 - EGR System Failure
33 - A/C Clutch Relay Circuit Open Or Shorted
34 - Speed Control Solenoid Ciruit Open Or Shorted (Vacuum Or Vent)
37 - Torque Converter Clutch Solenoid Circuit Open Or Shorted
41 - Generator Field Not Switching Properly
42 - Auto Shutdown Relay Control Circuit Open Or Shorted Or No ASD Voltage
44 - Battery Temp Sensor Voltage Out Of Limit
45 - Overdrive Solenoid Circuit Open Or Shorted
46 - Charging System Voltage Too High
47 - Charging SYstem Voltage Too Low
51 - O2 Sensor Signal Stays Below Center (Lean)
52 - O2 Sensor Signal Stays Above Center (Rich)
53 - Internal PCM Failure
54 - Sync Pick-Up Signal Not Detected (Camshaft Position Sensor/Ignition Pickup)
62 - PCM Failure SRI Miles Not Stored
63 - PCM Failure EEProm Write Denied

55 End Of Codes

These codes are good for years 93, 94 and 95.

The above procedure will work for 96 and up but be aware an OBD II scanner will be needed as the above codes could have multiple meanings.


Transmission codes for 42re and mabye others, same routine but displayed via the overdrive light.

11 - Engine RPM Input
12 - Output shaft sensor input
13 - Vehicle speed input
14 - Governor pressure sensor input
15 - Throttle position sensor input
16 - Transmission fluid temp input
17 - Overdrive override switch input
18 - System voltage
19 - Internal fault in module
21 - Governor pressure solenoid output
22 - Overdrive solenoid output
23 - Converter clutch solenoid output
24 - Overdrive override lamp output
25 - Internal fault in module
26 - Governor pressure sensor offset drift
55 - end of codes

carderzj

Thank you for that code list, Hatch! Some interesting things for me to check out looks like.