Project "Hippo"...black 99 XJ
CF Veteran
Joined: Nov 2011
Posts: 1,314
Likes: 0
From: Las Vegas, NV - St. George, UT
Year: 1996
Model: Cherokee
Engine: 4.0
What happened? Is it about the LCA?
Oh and I called around to some shops, $10-$12 for mount and balance... I thougt you got a good deal at Adams...
Oh and I called around to some shops, $10-$12 for mount and balance... I thougt you got a good deal at Adams...
Thread Starter
CF Veteran
Joined: Jan 2011
Posts: 1,894
Likes: 4
From: Las Vegas
Year: 1999
Model: Cherokee
Engine: 4.0
Still leaking after he replaced it.
Thought you might wanna hassle him for a SYE package deal.
Fixed!
After replacing the seal for the second time and its still leaking.
Upon further inspection (by Adamsdriveshaft), they concluded that i may have a bent output shaft and a replacement was in order.
With new output shaft and tail housing installed, leak has gone....didn't drive much, but so far no leak
.
Last edited by BotakBeng; May 2, 2012 at 08:20 PM.
CF Veteran
Joined: Nov 2011
Posts: 1,314
Likes: 0
From: Las Vegas, NV - St. George, UT
Year: 1996
Model: Cherokee
Engine: 4.0
Originally Posted by BotakBeng
Still leaking after he replaced it.
Thought you might wanna hassle him for a SYE package deal.
Thought you might wanna hassle him for a SYE package deal.
CF Veteran
Joined: Nov 2011
Posts: 1,314
Likes: 0
From: Las Vegas, NV - St. George, UT
Year: 1996
Model: Cherokee
Engine: 4.0
Originally Posted by BotakBeng
Yeah, it came with the rugged ridge SYE.
Planning on going Tue early morn, tx me if you wanna go.
Planning on going Tue early morn, tx me if you wanna go.
Thread Starter
CF Veteran
Joined: Jan 2011
Posts: 1,894
Likes: 4
From: Las Vegas
Year: 1999
Model: Cherokee
Engine: 4.0
RC Performance 2.2 Steering Stabilizer
Got a lot of work done today.
Installed my RC Performance 2.2 Steering Stabilizer.
(Overrate!)
Gave Hippo her first wash and clean up my garage.
Before and after pics
Last poser shots, i promise
Have to remove my bumper caps as the tires was rubbing. I suspect it was my wheel's backspace (3.75), anyway, time to hunt for some bumper or do some trimming.
Installed my RC Performance 2.2 Steering Stabilizer.
(Overrate!)
Gave Hippo her first wash and clean up my garage.
Before and after pics
Last poser shots, i promise
Have to remove my bumper caps as the tires was rubbing. I suspect it was my wheel's backspace (3.75), anyway, time to hunt for some bumper or do some trimming.
Last edited by BotakBeng; Apr 16, 2012 at 11:34 PM.
Thread Starter
CF Veteran
Joined: Jan 2011
Posts: 1,894
Likes: 4
From: Las Vegas
Year: 1999
Model: Cherokee
Engine: 4.0
RC rear leaf springs is gonna cost me my kidney....
Hope this would expedite the breaking in...
Relocate my vacuum ball and horns, also trim the fender well , getting ready for my "custom" bumper
Hope this would expedite the breaking in...
Relocate my vacuum ball and horns, also trim the fender well , getting ready for my "custom" bumper
Last edited by BotakBeng; Apr 22, 2012 at 03:13 PM.
Thread Starter
CF Veteran
Joined: Jan 2011
Posts: 1,894
Likes: 4
From: Las Vegas
Year: 1999
Model: Cherokee
Engine: 4.0
Shackle angle doesn't look good, leaf springs too short imo.
I'm getting around 5.5" front and 6.25" rear of lift so far, looks like there is quite a bit of breaking in.
Measuring Lift Height
>Center of the hub to bottom of the flares, stock=17.5" front and 17" rear.
>Another way is to measure the top of the axle tube to the frame rail, stock = 6.75 front and 6" rear.
Anything more would be the lift height.
CF Veteran
Joined: Nov 2011
Posts: 1,314
Likes: 0
From: Las Vegas, NV - St. George, UT
Year: 1996
Model: Cherokee
Engine: 4.0
Thinking about ordering the RC disconnects, what are your thoughts on them? Have you disconnected them yet?
I had the old Skyjacker's with the double pins, those suck. Then I drove around with the front sway bar off because I could never get the discos back on.
I had the old Skyjacker's with the double pins, those suck. Then I drove around with the front sway bar off because I could never get the discos back on.