My 1988 XJ Build. "Whitey"
#16
Member
Thread Starter
Join Date: Jan 2010
Location: CA
Posts: 231
Likes: 0
Received 0 Likes
on
0 Posts
Year: 1988
Model: Cherokee
Engine: 4.0
Now i'm getting frustrated....again... I got the idle down to around 1000 rpms via the little screw. Idles fine, when cold. Now when the engine gets up to temp. it runs really rough, and dies. Any suggestions??
#22
Member
Thread Starter
Join Date: Jan 2010
Location: CA
Posts: 231
Likes: 0
Received 0 Likes
on
0 Posts
Year: 1988
Model: Cherokee
Engine: 4.0
A little out of order but whatever..... This was Goatfest 2011 in JV with NAXJA... Not too bad..
^^^^^Dude that burger was so freaking good...^^^^^
^^^^^Dude that burger was so freaking good...^^^^^
#24
Member
Thread Starter
Join Date: Jan 2010
Location: CA
Posts: 231
Likes: 0
Received 0 Likes
on
0 Posts
Year: 1988
Model: Cherokee
Engine: 4.0
And all the parts that have broken....and them some that aren't pictured...
Got it towed for Reg...
Busted up the D35 spiders..
Got the jeep and the Scion in the same garage...
My little helper..
Got a lower mileage engine to swap
Then took it out..
Then changed the ball joints....again...
Got the new to me D44...5.13's....full spool...Chromo's...trussed w/ a skid plate....still sitting in my garage...
Then I broke a U-joint
Then I blew a shock..
Fixed that...and bought a new toy
Then I blew the hub...lol
AAAANNNDDD since all of this I have busted two more u-joints. Stupid u-joints...
Added a new 1-ton steering setup. Adj. UCA's, new CD player and speakers, and a new fuel pump. I'm probably forgetting some crap but o well... I have hundreds of pics I need to go thru.
Got it towed for Reg...
Busted up the D35 spiders..
Got the jeep and the Scion in the same garage...
My little helper..
Got a lower mileage engine to swap
Then took it out..
Then changed the ball joints....again...
Got the new to me D44...5.13's....full spool...Chromo's...trussed w/ a skid plate....still sitting in my garage...
Then I broke a U-joint
Then I blew a shock..
Fixed that...and bought a new toy
Then I blew the hub...lol
AAAANNNDDD since all of this I have busted two more u-joints. Stupid u-joints...
Added a new 1-ton steering setup. Adj. UCA's, new CD player and speakers, and a new fuel pump. I'm probably forgetting some crap but o well... I have hundreds of pics I need to go thru.
Last edited by Peacefrog53; 08-30-2012 at 11:00 AM.
#25
Member
Thread Starter
Join Date: Jan 2010
Location: CA
Posts: 231
Likes: 0
Received 0 Likes
on
0 Posts
Year: 1988
Model: Cherokee
Engine: 4.0
Yea Buddy!!!
Went 4.56's, got that 44 in there, replaced all the u-joints on the truck, fabbed up a little bed cage for the shocks to go through the floor, new bump stops, relocated the battery, and got all the lights working.
O and for the record. Always use a full mask when welding. That arc burn hurt ten times more than any sunburn i've ever had. And probably ten times as cancerous too. lol
Went 4.56's, got that 44 in there, replaced all the u-joints on the truck, fabbed up a little bed cage for the shocks to go through the floor, new bump stops, relocated the battery, and got all the lights working.
O and for the record. Always use a full mask when welding. That arc burn hurt ten times more than any sunburn i've ever had. And probably ten times as cancerous too. lol
#28
Member
Thread Starter
Join Date: Jan 2010
Location: CA
Posts: 231
Likes: 0
Received 0 Likes
on
0 Posts
Year: 1988
Model: Cherokee
Engine: 4.0
#29
Member
Thread Starter
Join Date: Jan 2010
Location: CA
Posts: 231
Likes: 0
Received 0 Likes
on
0 Posts
Year: 1988
Model: Cherokee
Engine: 4.0
#30
Member
Thread Starter
Join Date: Jan 2010
Location: CA
Posts: 231
Likes: 0
Received 0 Likes
on
0 Posts
Year: 1988
Model: Cherokee
Engine: 4.0
Shweeettt.... LCA mount braces and C gussets. Got the parts for my new tbar and 12 gauge for plating the body.
Yea I need to practice my welding....
Yea I need to practice my welding....