jeep cherokee 2wd to a 4x4
#1
Newbie
Thread Starter
Join Date: Apr 2015
Location: New Orleans
Posts: 3
Likes: 0
Received 1 Like
on
1 Post
Year: 2000
Model: Cherokee
Engine: 4.0
jeep cherokee 2wd to a 4x4
I just purchased a 2000 jeep cherokee xj 4x4 from a friend for $450 engine transfer case transmission all good but body is rusted out very bad can I just take all 4x4 parts off and bolt in a 2wd jeep and what year jeepS can I use with out haveING yo make modifications I would like to be able to just bolt everything up
The following users liked this post:
ijeeep (05-04-2020)
#2
Senior Member
Join Date: Oct 2012
Location: Gainesville,FL
Posts: 989
Likes: 0
Received 2 Likes
on
2 Posts
Year: 1996
Model: Cherokee
Engine: 4.0
First off, why is this in the Builds section?????? The 2000 XJ has a ****ty head prone to cracking, the front axle is a LP Dana30. Everything is easily swapped over but it takes time and tools. If you have 2WD you'll need to cut out the tunnel for the selector lever for 4wd. If everything was rusted, you'll need to replace u-joints, brakes, wheel bearings, etc. Don't forget to wire up the part time light.
The following users liked this post:
ijeeep (05-04-2020)
#4
It sounds like you bought a 4x4 Cherokee with a decent drive train. I won't say good because it has the crappy head. You are looking for a rig to put it into. I would just purchase another 4x4 rig instead of a 2wd rig. You can swap the 4x4 drive train into a 2wd but will take some modification in a few places. Part out the 4x4 rig and build up funds to purchase an operational rig that is set up how you want it.
#5
Newbie
Thread Starter
Join Date: Apr 2015
Location: New Orleans
Posts: 3
Likes: 0
Received 1 Like
on
1 Post
Year: 2000
Model: Cherokee
Engine: 4.0
What all would I have to modify??
What would I have to modify?
It sounds like you bought a 4x4 Cherokee with a decent drive train. I won't say good because it has the crappy head. You are looking for a rig to put it into. I would just purchase another 4x4 rig instead of a 2wd rig. You can swap the 4x4 drive train into a 2wd but will take some modification in a few places. Part out the 4x4 rig and build up funds to purchase an operational rig that is set up how you want it.
What would I have to modify?
#6
Senior Member
Join Date: Oct 2012
Location: Gainesville,FL
Posts: 989
Likes: 0
Received 2 Likes
on
2 Posts
Year: 1996
Model: Cherokee
Engine: 4.0
READ!!!! There's google, just type in 2WD to 4WD conversion:cherokeeforum
You'll need to cut the tunnel to run a selector lever, other assorted mounts, electronics, etc. If you don't have the tools or space to do this, it's easier to find another 4x4 rig and use the rusty one for parts
You'll need to cut the tunnel to run a selector lever, other assorted mounts, electronics, etc. If you don't have the tools or space to do this, it's easier to find another 4x4 rig and use the rusty one for parts
#7
Like docmedpros said you have to cut the trans tunnel for the shifter. You also have some wiring to do for the lights to the dash and the shifter lights. You also need vacuum lines from the t-case to the front axle. You also have to get the steering tube out and put in the front axle and drive shaft along with adding the T-case to the trans. It can be done, but will require moderate mechanical skill and some fabrications.
Trending Topics
#8
what about conversion years? i have a 2wd 97 4.0L with blown trans and a 4x4 95 4.0L with a blown motor. i know they're to different models but would everything bolt up with little modding?
#9
Xj 2wd to 4wd
There is no cutting holes in the tunnel for the transfercase shifter there simply is a bolted in plate where it would be. Just remove the bolts and bolt the shifter and linkage in. I have done this swap in my driveway in a day and a half being as I rolled my xj and bought as clean 2wd same year and turned it in to a 4wd. You have to swap trans Transfercase front diff and transfercase linkage and shifter.and front drive shaft. With some mechanical ability it is quite easy.
#10
Wiring problems on transmission swap
I recently swapped my 98 2wd to 4wd from another 98. Got it all done and the wiring harnesses matched up but the colors are different. Trying to do a pin out from the shop manual but having a hard time. It cranks but no start. I have changed out the cps. I have tested the tcu and pcm (I have another 98 4x4 to swap parts for testing). Can’t crack the code on the difference in wires. There are two harnesses one grey one black. I know one is the nss. The other reads speed and shifts the transmission. Any help would be great.
#11
CF Veteran
Join Date: Sep 2017
Location: MO
Posts: 1,553
Received 304 Likes
on
253 Posts
Year: 1996
Model: Cherokee (XJ)
Engine: 4.0
I recently swapped my 98 2wd to 4wd from another 98. Got it all done and the wiring harnesses matched up but the colors are different. Trying to do a pin out from the shop manual but having a hard time. It cranks but no start. I have changed out the cps. I have tested the tcu and pcm (I have another 98 4x4 to swap parts for testing). Can’t crack the code on the difference in wires. There are two harnesses one grey one black. I know one is the nss. The other reads speed and shifts the transmission. Any help would be great.
Thread
Thread Starter
Forum
Replies
Last Post
rusty_bucket
Stock XJ Cherokee Tech. All XJ Non-modified/stock questions go here
3
08-29-2015 06:42 AM
Currently Active Users Viewing This Thread: 1 (0 members and 1 guests)