1997 XJ on FULL WIDTHS and 44's
12-12-2011, 04:14 PM
#76
MJ>XJ
Join Date: Mar 2009
Location: Griffin, G.A.
Posts: 17,836
Likes: 0
Received 4 Likes
on
3 Posts
Year: 1990
Model: Comanche
Engine: 4.0 I6
Mud trucks are thrown together cause they never lasr long... Motor blows... Tranny burns... Roll it at that height and its done... Poor mans offroading... Lol... Now some can do it up right... Those guys love to fix... I like driving...
12-12-2011, 09:38 PM
#81
Senior Member
Join Date: May 2010
Location: Northern Indiana
Posts: 639
Likes: 0
Received 1 Like
on
1 Post
Year: 1990
Model: Cherokee
Engine: Renix 4.0
Awesome that you are pushing through on the build! Seriously.
For sure weird though how you started this for help, but are the expert.
This thread has my attention. The first build I have seen like this. Entertaining!
And just because I am good at beating a dead horse... se...ar..c.... nevermind.
For sure weird though how you started this for help, but are the expert.
This thread has my attention. The first build I have seen like this. Entertaining!
And just because I am good at beating a dead horse... se...ar..c.... nevermind.
12-12-2011, 10:23 PM
#82
Old Skewl CF like a Sir
Join Date: Feb 2008
Location: Fort Myers, FL
Posts: 4,355
Likes: 0
Received 3 Likes
on
3 Posts
Year: 1996
Model: Cherokee
Engine: 4.0L High Output OBDII
Alright Margret, hold my calls.
Juancho, fetch me my coat.
Ready?
Okay good.
So, let me get this straight. You asked a bunch of questions, got answers, but not the ones you were looking for. So you argue your way into convincing those who have already gone through above steps, that you are infact correct in your findings. And your last build, on 38" mudders, never broke anything, even with a "locked" which at this rate I'm willing to bet was "welded" at best, rear end. All this of course on a rig that appeared to have a Renix clip, so I'd be willing to bet it didn't have enough grunt to break a stock u-joint at a severe angle, which is probably close to the setup the old XJ was running.
So, because your so intrigued by your previous home built billyjoebobthortan lift setup on your last XJ, you've taken it upon yourself to re-engineer the triangulation of a vehicles suspension, without so much as even a calculator.
Listen bub, I understand. I live 50 minutes South of you. I know what Venice is like. I'd be bored as hell there too. And yes again, I've been to Redneck Yacht Club, quite a few times. And its your Jeep, build it as you wish. But the irony of the situation is, this website isn't Pirate 4x4. This isn't ChucksTrucks. This isn't the Facebook page of RYC. This is CherokeeForum.
We're nice, we're helpful. But we don't tolerate stupidity. Build however you want, we'll keep you around for the lol factor. You can't step in the ring with Ali and just think you can box. These guys are trying to help you.
Better yet. Gimme the specs on the XJ, gimme an obo on it. I'll bring a trailer, take it off your hands, and you can get yourself that F-250 you've been dying to get. Hell, I'll help you rig a pair of stars & bars off it, some dual whips, we'll even make a removable stripper pole for RYC.
Also, anytime there is a red line under a word, please right click and select the word you meant to spell.
Juancho, fetch me my coat.
Ready?
Okay good.
So, let me get this straight. You asked a bunch of questions, got answers, but not the ones you were looking for. So you argue your way into convincing those who have already gone through above steps, that you are infact correct in your findings. And your last build, on 38" mudders, never broke anything, even with a "locked" which at this rate I'm willing to bet was "welded" at best, rear end. All this of course on a rig that appeared to have a Renix clip, so I'd be willing to bet it didn't have enough grunt to break a stock u-joint at a severe angle, which is probably close to the setup the old XJ was running.
So, because your so intrigued by your previous home built billyjoebobthortan lift setup on your last XJ, you've taken it upon yourself to re-engineer the triangulation of a vehicles suspension, without so much as even a calculator.
Listen bub, I understand. I live 50 minutes South of you. I know what Venice is like. I'd be bored as hell there too. And yes again, I've been to Redneck Yacht Club, quite a few times. And its your Jeep, build it as you wish. But the irony of the situation is, this website isn't Pirate 4x4. This isn't ChucksTrucks. This isn't the Facebook page of RYC. This is CherokeeForum.
We're nice, we're helpful. But we don't tolerate stupidity. Build however you want, we'll keep you around for the lol factor. You can't step in the ring with Ali and just think you can box. These guys are trying to help you.
Better yet. Gimme the specs on the XJ, gimme an obo on it. I'll bring a trailer, take it off your hands, and you can get yourself that F-250 you've been dying to get. Hell, I'll help you rig a pair of stars & bars off it, some dual whips, we'll even make a removable stripper pole for RYC.
Also, anytime there is a red line under a word, please right click and select the word you meant to spell.
12-13-2011, 12:57 AM
#85
Member
Join Date: Oct 2011
Location: oregon
Posts: 235
Likes: 0
Received 0 Likes
on
0 Posts
Year: 1991
Model: Cherokee
Engine: 4.0
Oh man come on buddy do stuff right and take some advice from the guys. I don't think you need to spend a ton of money but spend it where it counts. I'm glad to hear you decided to build your brackets Instead of using the stock ones. Here's an idea sell your stock axles and buy hydro assist and a Bunch of steel to plate the frame for your steering and link mounts and axle brackets and maybe a Durango box. As far as axles I would leave that 44 open don't weld it you won't be able to turn on ice haha. I think you'll be alright with 4.10 gears for a while I ran them with 40s for a while it's fine in low range and from the sounds of it that's all your gonna need for mud wheeling. Anyway man Good luck. Also Carry extra shafts for that 44!
12-13-2011, 08:12 AM
#89
Seasoned Member
Thread Starter
Join Date: Nov 2011
Location: venice FL
Posts: 444
Likes: 0
Received 0 Likes
on
0 Posts
Year: 1997
Model: Cherokee
Engine: 4.0 HO
MUD TRUCK!! the front axle is mounted i still got to plate the frame and make coil spring mounts on top of the 44 heres a pic of it 