Northern Utah BS thread
05-01-2011, 10:25 PM
#6496
CF Veteran
Thread Starter
Join Date: Sep 2009
Location: West Valley
Posts: 3,612
Likes: 0
Received 0 Likes
on
0 Posts
Year: 1998
Model: Cherokee (XJ)
Engine: 4.0
Guys night out was a blast, thanks to everyone who made it out. We definately need to do that some more. My son was extra stoked by the fact that you guys made him feel like part of the group, even though he does'nt have his Jeep yet.
05-01-2011, 11:04 PM
#6498
CF Veteran
Join Date: May 2009
Location: SLC, UT
Posts: 6,328
Likes: 0
Received 1 Like
on
1 Post
Year: 1989 2 door
Model: Cherokee
Engine: 4.0
I had a pretty productive day too. Got my axle in, fixed the wheel seal cause it was all screwed after the axle break, fixed my falling apart exist by pulling the muffler back out Haha sounds SICK tho, & cut my LF fender a little higher! (RF soon lol)
05-02-2011, 12:00 AM
#6499
CF Veteran
Join Date: Sep 2010
Location: Springville, UT
Posts: 1,649
Likes: 0
Received 1 Like
on
1 Post
Year: 1993
Model: Grand Cherokee
Engine: 5.2 V8, Dual cold air, dual batts, E-fan, Sanden OBA
Well I installed new balljoints (again) and decided to go play on the hill with my buddy. He busted the spider gears in his front Dana 44, and me being me decided to climb over some massive rocks (picture 2 rocks side by side with about a 2 foot gap between them and as high as my hood) well I got sideways in between them and the SOB climbed right over and out, bad thing was that I ripped a big chunk out of the sidewall of my brand new tire, and I bent my rock sliders all to he'll. But hey so far no one around here has conquered that obstacle besides me!
05-02-2011, 07:49 PM
#6504
Member
Join Date: Nov 2009
Location: Eagle Mountain, Utah
Posts: 194
Likes: 0
Received 0 Likes
on
0 Posts
I stared at mine and tried to figure out the whole money thing so i can start modifiying again. oh and ran 9 calls at work so far including a baby delivery and 2 heart attacks. Been a busy day 
05-02-2011, 09:02 PM
#6506
Senior Member
Join Date: Mar 2011
Location: provo, utah
Posts: 711
Likes: 0
Received 0 Likes
on
0 Posts
Year: 1995
Model: Cherokee
Engine: 4.0
Finshed product cost me 25 bucks (that was for the shiv an axe at habor ) and about 20 min to make vs. around 80 just for the brakets in a mag or off line
05-02-2011, 11:55 PM
#6509
Seasoned Member
Join Date: Apr 2011
Location: KEARNS, UT.
Posts: 297
Likes: 0
Received 0 Likes
on
0 Posts
Year: 1995
Model: Cherokee
Engine: 4.0L Inline 6
Originally Posted by Celticclove
Finshed product cost me 25 bucks (that was for the shiv an axe at habor ) and about 20 min to make vs. around 80 just for the brakets in a mag or off line
p.s. you did a good job!
05-03-2011, 12:20 AM
#6510
CF Veteran
Join Date: Jan 2009
Location: Utardiland
Posts: 1,703
Likes: 0
Received 0 Likes
on
0 Posts
Year: whats left of a 91
Model: Cherokee
Engine: one that makes noise
i would make your shovel and axe mount lockable if they are not already.
i lost 2 axe's and a shovel with a similar mount cause apparently someone needed them more than me.
i lost 2 axe's and a shovel with a similar mount cause apparently someone needed them more than me.