new to the forum in Georgia
#1
Newbie
Thread Starter
Join Date: May 2013
Location: Georgia
Posts: 18
Likes: 0
Received 0 Likes
on
0 Posts
Year: 1994
Model: Cherokee
Engine: 4.0
Hello all my name is Jimmy and I just bought my first Jeep. It is a 1994 Cherokee 4.0 in line six automatic transmission NOT 4X4. I got it for $200 the body is in dang near perfect condition couldn't pass it up. To top it off it passed emissions. I'm trying to see if anyone has a picture of their fuse panel with diagram. My heater nor AC isn't blowing and I'm not sure why.
Last edited by jimdawg64; 05-11-2013 at 09:30 AM.
#2
CF Veteran
Join Date: Aug 2011
Location: Nor-Cal Coast
Posts: 10,489
Likes: 0
Received 17 Likes
on
17 Posts
Year: 90,84
Model: Cherokee
Engine: 4.0,2.5
Welcome Jim! I can't help you right now with that diagram. It IS always good to fill out your info so in later posts people can see right off what you have. Sometimes the weekends are slower than the week days, good luck!
#4
CF Veteran
Join Date: Apr 2012
Location: Wisconsin
Posts: 5,302
Likes: 0
Received 19 Likes
on
16 Posts
Model: Cherokee
Check the plug at the blower motor, you may find it melted.
Fuse diagram for a '95 here, I think 94 is the same:
https://www.cherokeeforum.com/f2/nee...ram-plz-53194/
Fuse diagram for a '95 here, I think 94 is the same:
https://www.cherokeeforum.com/f2/nee...ram-plz-53194/
#6
Newbie
Thread Starter
Join Date: May 2013
Location: Georgia
Posts: 18
Likes: 0
Received 0 Likes
on
0 Posts
Year: 1994
Model: Cherokee
Engine: 4.0
Thanks again Radi. The diagram was an exact match. However the plug to the blower motor in perfect condition. So I checked the motor by running electric wires directly from the battery to the blower motor plug and it turned on. So the motor works.
I removed the dash and pulled the controls for the heater and AC and one of the wiring harnesses was melted and the receivers for the harness were fried.
Does anyone know how many years they used the same controls for the heater and AC?
I removed the dash and pulled the controls for the heater and AC and one of the wiring harnesses was melted and the receivers for the harness were fried.
Does anyone know how many years they used the same controls for the heater and AC?
Trending Topics
#10
CF Veteran
Join Date: Apr 2012
Location: Wisconsin
Posts: 5,302
Likes: 0
Received 19 Likes
on
16 Posts
Model: Cherokee
Thanks again Radi. The diagram was an exact match. However the plug to the blower motor in perfect condition. So I checked the motor by running electric wires directly from the battery to the blower motor plug and it turned on. So the motor works.
I removed the dash and pulled the controls for the heater and AC and one of the wiring harnesses was melted and the receivers for the harness were fried.
Does anyone know how many years they used the same controls for the heater and AC?
I removed the dash and pulled the controls for the heater and AC and one of the wiring harnesses was melted and the receivers for the harness were fried.
Does anyone know how many years they used the same controls for the heater and AC?
94 95 96 look like they use the same HVAC controls to me. Could be more years than that. '97 went to the rotary controls, I'm not sure if the wiring is interchangeable but I suspect not.
Last edited by Radi; 05-13-2013 at 10:52 PM.
#12
Newbie
Thread Starter
Join Date: May 2013
Location: Georgia
Posts: 18
Likes: 0
Received 0 Likes
on
0 Posts
Year: 1994
Model: Cherokee
Engine: 4.0
So apparently the burning out of the harness and receiver happens often. I must of looked at 10 different Cherokees today and finally found one in descent condition. The good news is I now have heat and AC. Thanks again for all the help.
Thread
Thread Starter
Forum
Replies
Last Post
Currently Active Users Viewing This Thread: 1 (0 members and 1 guests)