left my drive shaft on the free way need help
#1
Newbie
Thread Starter
Join Date: Sep 2009
Posts: 23
Likes: 0
Received 0 Likes
on
0 Posts
Year: 1989
Model: Cherokee
Engine: 4.0L
left my drive shaft on the free way need help
so earlier this week i was driving on the free way felt a small vibration and less then a mile later large vibration and the pop next thing i know i see the drive shaft flying through the air.
well got it off the road but the drive shaft was toast as the semi truck ran it over and then a car and so on left it for dead o well
upon further inspection after trailering it home, all that was left from the bell housing on the transfer case was 3 bolts and a 1 inch piece of metal under each bolt
any who no big deal i have another parts truck well i do now have to buy it from a family member who has had it sitting there and small parts no big deal but once i get into the drive line .... time to pony up the cash
any way i digress my question is i am having problems getting the drive shaft to slip onto the output shaft it goes on about 1 inch and just stops i have rotated all the way around different angles but no luck i know its prob cause im frustrated any advice on why this wont go on?
whats the chance i bent the output shaft. output bearings still in good shape.
well got it off the road but the drive shaft was toast as the semi truck ran it over and then a car and so on left it for dead o well
upon further inspection after trailering it home, all that was left from the bell housing on the transfer case was 3 bolts and a 1 inch piece of metal under each bolt
any who no big deal i have another parts truck well i do now have to buy it from a family member who has had it sitting there and small parts no big deal but once i get into the drive line .... time to pony up the cash
any way i digress my question is i am having problems getting the drive shaft to slip onto the output shaft it goes on about 1 inch and just stops i have rotated all the way around different angles but no luck i know its prob cause im frustrated any advice on why this wont go on?
whats the chance i bent the output shaft. output bearings still in good shape.
#3
Junior Member
Join Date: Jun 2009
Posts: 44
Likes: 0
Received 0 Likes
on
0 Posts
Year: 1998
Model: Cherokee
Engine: 4.0
There's definitely a good chance you bent the output shaft. That much mass spinning fast enough to scoot you down a freeway, has a whole lot of leverage when one end becomes unsecured.
#7
Trending Topics
#8
MJ>XJ
Join Date: Mar 2009
Location: Griffin, G.A.
Posts: 17,836
Likes: 0
Received 4 Likes
on
3 Posts
Year: 1990
Model: Comanche
Engine: 4.0 I6
i take it you used the tailshaft and the driveshaft both out of the same vehicle... so they should work unless theres something else wrong which would be my guess...
#9
Newbie
Thread Starter
Join Date: Sep 2009
Posts: 23
Likes: 0
Received 0 Likes
on
0 Posts
Year: 1989
Model: Cherokee
Engine: 4.0L
would have loved to have gotten my old drive shaft off the road for something to hang in the garage but it was not safe to get it. i did call caltrans and tell them there was debris in the road. but 91 free way here in so cal at 230 you have just enough people to not allow you to play on the free way it was just around a bend and avrg speed was 75 or so
well im gonna pull the bell housing off the t case and see if it will slip on. its not like i cant get it to go on at all instead it goes on about an inch and then stops like metal running into metal even gives a nice little "Tink"
well im gonna pull the bell housing off the t case and see if it will slip on. its not like i cant get it to go on at all instead it goes on about an inch and then stops like metal running into metal even gives a nice little "Tink"
#11
Newbie
Thread Starter
Join Date: Sep 2009
Posts: 23
Likes: 0
Received 0 Likes
on
0 Posts
Year: 1989
Model: Cherokee
Engine: 4.0L
ill give that a try later today. if its a tight fit more lube :P
ps. hey mike hows the off roading up there in paso have family up there was thinking after i get some more work done on my truck, driving it up there for a weekend
ps. hey mike hows the off roading up there in paso have family up there was thinking after i get some more work done on my truck, driving it up there for a weekend
#14
Newbie
Thread Starter
Join Date: Sep 2009
Posts: 23
Likes: 0
Received 0 Likes
on
0 Posts
Year: 1989
Model: Cherokee
Engine: 4.0L
ok well last Friday got the drive shaft to slip on, it had to do with the seal not lining up right,great call mike.
the problem i have now is the drive shaft i have is about 1 inch to long v.v well to the bone yard Monday morning for one that will fit until i can get the lift onto my truck.
the problem i have now is the drive shaft i have is about 1 inch to long v.v well to the bone yard Monday morning for one that will fit until i can get the lift onto my truck.