D35 Setup specs
#1
Junior Member
Thread Starter
Join Date: Sep 2011
Location: Calgary, AB
Posts: 40
Likes: 0
Received 1 Like
on
1 Post
Year: 1991
Model: Cherokee
Engine: 4.0
D35 Setup specs
What are there for specs on rebuilding my 3.07 open Dana 35? I need to put in new diff bearings because the PO put in a new pinion seal and never tightened the nut to spec now I have noise when I'm on the throttle. My unit is a 1991 with the AX15 and 4.0, and it also happens to be my daily driver. At the moment I can't afford to look for a Chry 8.25, and i want to keep the same ratio of which I don't see a 3.07 ring and pinion for the 8.25. So that is why I need to know what the setup specs are on the D35. Anyone have that information?
#3
CF Veteran
Join Date: Mar 2009
Location: Tenn. and Mich.
Posts: 28,068
Likes: 0
Received 6 Likes
on
6 Posts
Year: 2004
Model: Grand Cherokee
Engine: 4.7L V8
I did a search and found this. >http://www.sija.org/bounty/Misc/D35PinionSeal.pdf
Go to the part for pinion shaft seal replacement.
Read this too. >http://www.jeepforum.com/forum/f12/g...-101-a-623694/
Go to the part for pinion shaft seal replacement.
Read this too. >http://www.jeepforum.com/forum/f12/g...-101-a-623694/
Last edited by ol"blue; 10-19-2012 at 10:12 AM.
#4
Junior Member
Join Date: Oct 2010
Location: NW Oregon
Posts: 72
Likes: 0
Received 0 Likes
on
0 Posts
Year: 1993
Model: Cherokee
Engine: 4.0 HO
What are there for specs on rebuilding my 3.07 open Dana 35? I need to put in new diff bearings because the PO put in a new pinion seal and never tightened the nut to spec now I have noise when I'm on the throttle. My unit is a 1991 with the AX15 and 4.0, and it also happens to be my daily driver. At the moment I can't afford to look for a Chry 8.25, and i want to keep the same ratio of which I don't see a 3.07 ring and pinion for the 8.25. So that is why I need to know what the setup specs are on the D35. Anyone have that information?
#5
Junior Member
Thread Starter
Join Date: Sep 2011
Location: Calgary, AB
Posts: 40
Likes: 0
Received 1 Like
on
1 Post
Year: 1991
Model: Cherokee
Engine: 4.0
It's not that I'm just gonna have to replace the pinion seal again, just have to setup the ring and pinion to get some more life out of them till I can afford to replace both front and rear ring and pinions with something more appropraite, like 3.73's. I know the rear u-joint needs to be replaced, but I always thought that they needed to be replaced when they vibrated or sqeaked, not make a whining noise. I'm only running 235/75r15's and I don't plan on going any larger on those anytime soon, but I have read from the other posts on here about MPG going up by getting away from the 3.07's. Yes, my MPG is not as good as I want and i drive about 50 miles a day, and with gas prices the way they are, i need to find loopholes. Can't afford another small car at this time.
Last edited by myraus; 10-19-2012 at 12:53 PM.
Thread
Thread Starter
Forum
Replies
Last Post
Freakn
Stock XJ Cherokee Tech. All XJ Non-modified/stock questions go here
52
10-04-2015 06:34 AM
Stabsthedrama
Stock XJ Cherokee Tech. All XJ Non-modified/stock questions go here
15
10-03-2015 05:46 PM
TNXJsleeper
Stock XJ Cherokee Tech. All XJ Non-modified/stock questions go here
1
10-02-2015 08:04 PM
Currently Active Users Viewing This Thread: 1 (0 members and 1 guests)