Cherokee wont stat
#1
Newbie
Thread Starter
Join Date: Mar 2014
Posts: 1
Likes: 0
Received 0 Likes
on
0 Posts
Model: Cherokee
Cherokee wont stat
i have a 1990 jeep cherokee larado 4.0 inline 6
the starter was going bad so i replaced it and it ran no problem for 3 day. then i went to start to one morning and nothing. the temp gauge maxes out i can hear the fuel pump engage lights work. replaced the battery and the starter relay.
the starter was going bad so i replaced it and it ran no problem for 3 day. then i went to start to one morning and nothing. the temp gauge maxes out i can hear the fuel pump engage lights work. replaced the battery and the starter relay.
#2
Junior Member
Join Date: Jun 2012
Location: foco, co
Posts: 92
Likes: 0
Received 0 Likes
on
0 Posts
Year: 1993
Model: Cherokee
Engine: 4.0
Check for corrosion on your battery terminals and follow the ground and power wires to where they attach to check for corrosion as well.
#3
Banned
Join Date: Oct 2012
Location: USA
Posts: 1,744
Likes: 0
Received 1 Like
on
1 Post
Year: 1998
Model: Cherokee
Engine: 4.0L i6
No Start Checklist
NOT CRANKING
CRANKS, BUT NO START
Engine Bay Fuse Box (PDC)
Kick Panel Fusebox
Misc reading:
Replaced Crank Sensor, Pickup Coil, Spark Plugs, Wires, and Distributor Cap; unit still won’t start.
https://www.cherokeeforum.com/f2/non...writeup-71401/
https://www.cherokeeforum.com/f2/lon...8/#post2182489
http://www.jeepforum.com/forum/f11/p...l#post10006643
http://www.jeepforum.com/forum/f11/p...9/#post7683626
http://www.naxja.org/forum/showthread.php?t=101119
http://www.jeepforum.com/forum/f11/b.../#post14517948
NOT CRANKING
- Check battery voltage (12V)
- Clean/tighten battery terminals. (Loose and/or corroded?)
- Check Gear Selector (Make sure you're in Park)
- Neutral Safety Switch (Try to start in Neutral, not Park)
- Check grounds
- Is starter getting power? (With the key in the ON position, check for approximately full battery voltage at the starter.)
- Starter (Hit with hammer)
- Starter (Jump with screwdriver. Connect 2 highest bolts. 1 small. 1 big)
- Starter Motor Fuse #19 (Kick panel: Fuse #19 (10A red))
- Starter Motor Fuse #10 (Engine Bay Fuse Box (PDC). Fuse #10. See diagrams)
- Starter Motor Relay (Engine Bay Fuse Box (PDC). “Cube” relay at end of fusebox)
- Ignition Switch (Turn on the blower motor fan on for your heater with your key in the 'run' position. Turn the key to the 'start' position... the fan should turn off as it trys to crank over, indicating a good ignition switch.)
CRANKS, BUT NO START
- Is gas tank empty?
- Fuel pressure. 48psi (+/- 5psi). Listen for Fuel Pump?
- Fuel pump relay (Engine Bay Fuse Box (PDC). Fuse #22. See diagrams)
- Ignition fuse (Kick panel: Fuse #11 (20A))
- Check for spark.
- Bad spark plugs?
- Bad Distributor, Cap, Wires?
- Crank Position Sensor (CPS)
- Bad coil pack?
- Bad ECU?
- Testing the TPS
- IAC, TPS, CPK, MAP Failure Symptoms
Engine Bay Fuse Box (PDC)
Kick Panel Fusebox
Misc reading:
Replaced Crank Sensor, Pickup Coil, Spark Plugs, Wires, and Distributor Cap; unit still won’t start.
https://www.cherokeeforum.com/f2/non...writeup-71401/
https://www.cherokeeforum.com/f2/lon...8/#post2182489
http://www.jeepforum.com/forum/f11/p...l#post10006643
http://www.jeepforum.com/forum/f11/p...9/#post7683626
http://www.naxja.org/forum/showthread.php?t=101119
http://www.jeepforum.com/forum/f11/b.../#post14517948
Thread
Thread Starter
Forum
Replies
Last Post
Currently Active Users Viewing This Thread: 1 (0 members and 1 guests)