Cap, rotor and wire recommendations
#1
Seasoned Member
Thread Starter
Join Date: Dec 2011
Location: Wenatchee, WA
Posts: 319
Likes: 0
Received 0 Likes
on
0 Posts
Year: 1990
Model: Cherokee
Engine: 4.0L Renix
Cap, rotor and wire recommendations
I am going to do a little tune up and am wondering what I should get for my 90. I've seen this question asked on the forum, but they haven't been for my year XJ. I was looking at this cap and rotor: http://www.summitracing.com/parts/SUM-G5247/
and I haven't started looking at wires yet. But would that cap/rotor kit be good? Should I just go to my local O'Reilly's and get them or what?
and I haven't started looking at wires yet. But would that cap/rotor kit be good? Should I just go to my local O'Reilly's and get them or what?
#3
Senior Member
Join Date: Feb 2009
Location: Highlands Ranch Co.
Posts: 717
Likes: 0
Received 0 Likes
on
0 Posts
Year: 1985 shell
Model: Cherokee
Engine: 1996 6 cylinder Briggs & Stratton
ACCEL Accel - Distributor Cap
Part Number: 120330
Line: ACC
1 Year Limited Warranty
UPC: 30999761941
$18.99 Each
$16.99 Each
Your Summit choice, Accel, or better yet BWD and save some coin.
Part Number: 120330
Line: ACC
1 Year Limited Warranty
UPC: 30999761941
$18.99 Each
$16.99 Each
Your Summit choice, Accel, or better yet BWD and save some coin.
#4
Member
Join Date: Dec 2011
Location: Sterling, VA
Posts: 121
Likes: 0
Received 0 Likes
on
0 Posts
Year: 1999
Model: Cherokee
Engine: 4.0
Quadratec sells a kit with the Accel plugs, wires, cap and rotor. I have heard that you should really use the Champion factory plugs. But the kit was cheaper than I could get just cap, rotor and wires from my FLAPS so I bought that, and then got the Champions from NAPA. Working great so far (just a couple hundred miles on it) but the wires don't fit the stock loom, a couple of them are too short. Cap is a quality looking piece with brass terminals. I put some dielectric on the terminals and plug ends too to keep the boots from sticking and the corrosion away.
#5
CF Veteran
Join Date: Oct 2011
Location: Seal Beach, CA
Posts: 4,440
Likes: 0
Received 2 Likes
on
1 Post
Year: 1996
Model: Cherokee
Engine: 4.0 HO Straight Six
I just did a quick search on Summit for spark plug wires for your year and got 3 pages of results. You should upgrade to 8 mm wires. You could even go bigger (saw that there was even 10 mm wires that were offered). And yes, bigger is better in this case.
#6
CF Veteran
Join Date: Oct 2011
Location: Seal Beach, CA
Posts: 4,440
Likes: 0
Received 2 Likes
on
1 Post
Year: 1996
Model: Cherokee
Engine: 4.0 HO Straight Six
Quadratec sells a kit with the Accel plugs, wires, cap and rotor. I have heard that you should really use the Champion factory plugs. But the kit was cheaper than I could get just cap, rotor and wires from my FLAPS so I bought that, and then got the Champions from NAPA. Working great so far (just a couple hundred miles on it) but the wires don't fit the stock loom, a couple of them are too short. Cap is a quality looking piece with brass terminals. I put some dielectric on the terminals and plug ends too to keep the boots from sticking and the corrosion away.
And you don't need a loom anyways. The kit comes with clips but I chose not to do use them.
Edit: Ah, pooey. I didn't see what year your XJ was. Accel doesn't make a tune up kit for a '90. So it looks like you should piece it all together. You just want a cap with brass terminals and quality wires (I hear NAPA makes good stuff). As for the rotor, it honestly doesn't matter too much, just a new one will suffice.
Last edited by ZINGGG; 04-02-2012 at 07:19 PM.
Trending Topics
#8
Seasoned Member
Thread Starter
Join Date: Dec 2011
Location: Wenatchee, WA
Posts: 319
Likes: 0
Received 0 Likes
on
0 Posts
Year: 1990
Model: Cherokee
Engine: 4.0L Renix
How does this look?
Cap: http://www.summitracing.com/parts/ACC-120330/
Rotor: http://www.summitracing.com/parts/ACC-130229/
Wires: http://www.summitracing.com/parts/SUM-867625R/
Cap: http://www.summitracing.com/parts/ACC-120330/
Rotor: http://www.summitracing.com/parts/ACC-130229/
Wires: http://www.summitracing.com/parts/SUM-867625R/
#10
CF Veteran
Join Date: Nov 2011
Location: phoenix az
Posts: 1,290
Likes: 0
Received 0 Likes
on
0 Posts
Year: 1989
Model: Cherokee
Engine: 4.0l 6 cylinder
Originally Posted by shooting sticks
How does this look?
Cap: http://www.summitracing.com/parts/ACC-120330/
Rotor: http://www.summitracing.com/parts/ACC-130229/
Wires: http://www.summitracing.com/parts/SUM-867625R/
Cap: http://www.summitracing.com/parts/ACC-120330/
Rotor: http://www.summitracing.com/parts/ACC-130229/
Wires: http://www.summitracing.com/parts/SUM-867625R/
#11
Seasoned Member
Thread Starter
Join Date: Dec 2011
Location: Wenatchee, WA
Posts: 319
Likes: 0
Received 0 Likes
on
0 Posts
Year: 1990
Model: Cherokee
Engine: 4.0L Renix
#12
CF Veteran
Join Date: Nov 2011
Location: phoenix az
Posts: 1,290
Likes: 0
Received 0 Likes
on
0 Posts
Year: 1989
Model: Cherokee
Engine: 4.0l 6 cylinder
#13
Seasoned Member
Thread Starter
Join Date: Dec 2011
Location: Wenatchee, WA
Posts: 319
Likes: 0
Received 0 Likes
on
0 Posts
Year: 1990
Model: Cherokee
Engine: 4.0L Renix
#14
CF Veteran
Join Date: Oct 2011
Location: Seal Beach, CA
Posts: 4,440
Likes: 0
Received 2 Likes
on
1 Post
Year: 1996
Model: Cherokee
Engine: 4.0 HO Straight Six
Originally Posted by shooting sticks
Yea they don't have these ones in stock though haha.
#15
Seasoned Member
Join Date: Dec 2011
Location: Joliet, IL
Posts: 289
Likes: 0
Received 1 Like
on
1 Post
Year: 1998,2001
Model: Cherokee
Engine: 4.0
Just my $0.02. I don't much care what brand my cap/rotor are as long as they have brass terminals. As for wires I really like Belden wires from Napa. However that's my preference and it seems your choice on parts was a good one.