2001 with heat soak problem...how do I fix it?
09-16-2010, 03:15 PM
#1
Seasoned Member
Thread Starter
Join Date: Feb 2009
Location: OKC, OK
Posts: 309
Likes: 0
Received 0 Likes
on
0 Posts
Year: 2001
Model: Cherokee
Engine: 4.0L
2001 with heat soak problem...how do I fix it?
My 2001 XJ is having some heat soak problems and it's getting old....how do I fix it? Love the jeep but can't stand that if I do a short stop and bet back in it run terrible and pops a CEL and I have to wait till it cools off to go again.
What are my options?
thanks,
Bobby
What are my options?
thanks,
Bobby
09-16-2010, 03:43 PM
#3
CF Veteran
Join Date: Sep 2010
Location: Milwaukee, WI
Posts: 21,168
Likes: 0
Received 5 Likes
on
5 Posts
Year: 1987
Engine: Check
+1 on figuring out what codes have been tripped. That should be first on your priority list.
For actual solutions to higher running temps, look into lower temp thermostats. Do a coolant flush if you haven't, and make sure you use the propper water/coolant mix. If that is still not enough, look into electric fans and set them to turn on a bit sooner than they normally would.
As a last chance you can try upgrading your radiator, but that can be a bit more expensive than all the other 'fixes' combined.
For actual solutions to higher running temps, look into lower temp thermostats. Do a coolant flush if you haven't, and make sure you use the propper water/coolant mix. If that is still not enough, look into electric fans and set them to turn on a bit sooner than they normally would.
As a last chance you can try upgrading your radiator, but that can be a bit more expensive than all the other 'fixes' combined.
09-16-2010, 03:49 PM
#4
Seasoned Member
Thread Starter
Join Date: Feb 2009
Location: OKC, OK
Posts: 309
Likes: 0
Received 0 Likes
on
0 Posts
Year: 2001
Model: Cherokee
Engine: 4.0L
Misfire #3 P0303. I have a scan guage in my jeep so I can clear the code...but after sitting for about 15 mins after driving it and you get back in on a hot day....it does this....after cool down (of longer than 30 mins...helps if I open the hood too) it starts up and runs fine.
09-16-2010, 03:52 PM
#5
Seasoned Member
Thread Starter
Join Date: Feb 2009
Location: OKC, OK
Posts: 309
Likes: 0
Received 0 Likes
on
0 Posts
Year: 2001
Model: Cherokee
Engine: 4.0L
I though these jeeps did not like to run too cool.....I hear that 210 is were it likes to be to run well? BTW it only does this on really hot days with short stops in between driving to and fro.
09-16-2010, 04:26 PM
#6
Junior Member
Join Date: Jun 2009
Location: IL
Posts: 42
Likes: 0
Received 0 Likes
on
0 Posts
Year: 2001
Model: Cherokee
Engine: 4.0
There is a TSB for this issue:
1803103 - 4.0L ROUGH ENGINE IDLE AFTER RESTART FOLLOWING A HOT SOAK
Date: 09/05/03 (supercedes 1802702 dated 09/06/02)
Model Year(s): 1999-2004
Description: NOTE: This bulletin applies to vehicles equipped with a 4.0L engine. This bulletin involves the installation of a fuel injector insulator sleeve.
Details: Customers may describe a 20 to 30 second rough idle following the restart of a heat soaked engine. This condition may be most noticeable when the engine is restarted following a prior 10 to 20 minute heat soak in hot ambient conditions of approximately 32 C (90ºF) or higher. This condition may be consistent with short city stop-and-go driving trips and can be aggravated by the use of fuel with a high ethanol content. Depending upon various conditions a MIL may occur due to DTC P0303 - Cylinder #3 Misfire.
This condition may be caused by heat from the exhaust manifold that following engine shut down migrates to the area around injector #3 and causes fuel vapor to form within the injector. This in turn may cause a momentary misfire of cylinder #3 until the fuel vapor is cleared of injector #3. The insulator sleeve lowers the injector #3 temperature to a point below which the fuel will not normally vaporize.
If vehicle exhibits a rough idle, and if a misfire of cylinder #3 is observed following a 10 to 20 minute hot soak, perform the Repair Procedure.
Parts required:
56028371AA Ignition Wire Shield
Repair procedure:
1. Cut insulator sleeve, p/n 56028371AA, to make two (2) insulator sleeves about 25-30 mm (1 in.) in length. See diagram.
2. Install one sleeve around injector #3, with the slit on the upward facing side of the injector. Install the other sleeve with the slit on the downward facing side of the injector.
3. Confirm sleeve is flush to intake manifold surface around injector.
4. Check injector #3 wire and ensure that the injector is rotated to a 2 o'clock position (from driver’s side of vehicle).
Date: 09/05/03 (supercedes 1802702 dated 09/06/02)
Model Year(s): 1999-2004
Description: NOTE: This bulletin applies to vehicles equipped with a 4.0L engine. This bulletin involves the installation of a fuel injector insulator sleeve.
Details: Customers may describe a 20 to 30 second rough idle following the restart of a heat soaked engine. This condition may be most noticeable when the engine is restarted following a prior 10 to 20 minute heat soak in hot ambient conditions of approximately 32 C (90ºF) or higher. This condition may be consistent with short city stop-and-go driving trips and can be aggravated by the use of fuel with a high ethanol content. Depending upon various conditions a MIL may occur due to DTC P0303 - Cylinder #3 Misfire.
This condition may be caused by heat from the exhaust manifold that following engine shut down migrates to the area around injector #3 and causes fuel vapor to form within the injector. This in turn may cause a momentary misfire of cylinder #3 until the fuel vapor is cleared of injector #3. The insulator sleeve lowers the injector #3 temperature to a point below which the fuel will not normally vaporize.
If vehicle exhibits a rough idle, and if a misfire of cylinder #3 is observed following a 10 to 20 minute hot soak, perform the Repair Procedure.
Parts required:
56028371AA Ignition Wire Shield
Repair procedure:
1. Cut insulator sleeve, p/n 56028371AA, to make two (2) insulator sleeves about 25-30 mm (1 in.) in length. See diagram.
2. Install one sleeve around injector #3, with the slit on the upward facing side of the injector. Install the other sleeve with the slit on the downward facing side of the injector.
3. Confirm sleeve is flush to intake manifold surface around injector.
4. Check injector #3 wire and ensure that the injector is rotated to a 2 o'clock position (from driver’s side of vehicle).
Trending Topics
Thread
Thread Starter
Forum
Replies
Last Post
Psiegrist1
Stock XJ Cherokee Tech. All XJ Non-modified/stock questions go here
34
03-17-2022 02:15 PM
stimp774
Stock XJ Cherokee Tech. All XJ Non-modified/stock questions go here
20
04-16-2017 03:46 PM
shelby5041
Stock XJ Cherokee Tech. All XJ Non-modified/stock questions go here
39
11-07-2015 01:22 AM
synergy58
Stock XJ Cherokee Tech. All XJ Non-modified/stock questions go here
27
09-08-2015 11:51 PM
Currently Active Users Viewing This Thread: 1 (0 members and 1 guests)
