1987 Pontiac Trans Am GTA TONS OF MODS!
#1
Seasoned Member
Thread Starter
Join Date: Apr 2009
Location: Northeast PA
Posts: 288
Likes: 0
Received 0 Likes
on
0 Posts
Year: 1997
Model: Cherokee
Engine: 4.0, k&n intake Flomaster cat back
1987 Pontiac Trans Am GTA TONS OF MODS!
Hate to do it, but I'm in college and moneys tight. bought this car back in my senior year in high school. had it for a week and like a typical led footed teenager got in an accident with it. was hit in the passenger door/fender. had all frame work professionally done. had someone to do the body and interior(basically dicked me over after putting the wrong door on fixing some dents and painting the door and fender) put a new door on myself(red one didnt have the power options) Put a new dash in and finished the interior myself. car is 100% legal as it sits.
The Good;
Est. 600hp by previous owner(Tuned By Lingenfilter Performance Engineering)
less than 78,000 miles on body(less on motor)
Full roller 350
Paxton sn89 Supercharger(not currently on car, needs $200 part)
All forged internals
Aluminum heads
Accel super ram direct fuel injection setup
Aftermarket computer setup
billet throttle body
two stage nitrous kit
edelbrach ceramic mandrel bent headers
3" high flow cat
3" Custom single exhaust from headers back
Flowmaster muffler
MSD Pro Billet distributor
MSD 6AL ignition box
MSD blaster coil
MSD distributor cap and heli coil wires
Platinum sparkplugs
TCI Transmission
Summers Brothers Custom limited slip rear axel
Autometer tach
a pillar gauge pod with boost, oil, and fuel pressure gauges
hurst rachet shifter, with b&m T-handel **** with button
Remote nitrous bottle opener
Air/Fuel gauge, switches for N2o bottle, fuel pump, fan
The Bad;
Yellow Passanger Door
no ground effects on pass door, fender
No rear wing(GTA's came with rubber ones that the paint came off and the mounts rust out)
Supercharger needs an impeller shaft(about $200)
GTA door pannel dosent quite fit yellow door(may need GTA door, or some modification)
Interior Still needs some minor work(clips for pass A-pillar trim, work on the center consol)
Asking $5000 has at least 25k into the drivetrain
Ask any questions ya want, more than happy to awnser them, probably forgot some stuff.
The Good;
Est. 600hp by previous owner(Tuned By Lingenfilter Performance Engineering)
less than 78,000 miles on body(less on motor)
Full roller 350
Paxton sn89 Supercharger(not currently on car, needs $200 part)
All forged internals
Aluminum heads
Accel super ram direct fuel injection setup
Aftermarket computer setup
billet throttle body
two stage nitrous kit
edelbrach ceramic mandrel bent headers
3" high flow cat
3" Custom single exhaust from headers back
Flowmaster muffler
MSD Pro Billet distributor
MSD 6AL ignition box
MSD blaster coil
MSD distributor cap and heli coil wires
Platinum sparkplugs
TCI Transmission
Summers Brothers Custom limited slip rear axel
Autometer tach
a pillar gauge pod with boost, oil, and fuel pressure gauges
hurst rachet shifter, with b&m T-handel **** with button
Remote nitrous bottle opener
Air/Fuel gauge, switches for N2o bottle, fuel pump, fan
The Bad;
Yellow Passanger Door
no ground effects on pass door, fender
No rear wing(GTA's came with rubber ones that the paint came off and the mounts rust out)
Supercharger needs an impeller shaft(about $200)
GTA door pannel dosent quite fit yellow door(may need GTA door, or some modification)
Interior Still needs some minor work(clips for pass A-pillar trim, work on the center consol)
Asking $5000 has at least 25k into the drivetrain
Ask any questions ya want, more than happy to awnser them, probably forgot some stuff.
#6
Seasoned Member
Thread Starter
Join Date: Apr 2009
Location: Northeast PA
Posts: 288
Likes: 0
Received 0 Likes
on
0 Posts
Year: 1997
Model: Cherokee
Engine: 4.0, k&n intake Flomaster cat back
thanks, may still be available not lookin forward to sellin it. if i had the money i would keep it and finish it after the winter
#7
Newbie
Join Date: Sep 2009
Posts: 11
Likes: 0
Received 0 Likes
on
0 Posts
Year: 1994
Model: Cherokee
Engine: 4.0 Straight Six
Trending Topics
#9
Seasoned Member
Thread Starter
Join Date: Apr 2009
Location: Northeast PA
Posts: 288
Likes: 0
Received 0 Likes
on
0 Posts
Year: 1997
Model: Cherokee
Engine: 4.0, k&n intake Flomaster cat back
#12
Seasoned Member
Thread Starter
Join Date: Apr 2009
Location: Northeast PA
Posts: 288
Likes: 0
Received 0 Likes
on
0 Posts
Year: 1997
Model: Cherokee
Engine: 4.0, k&n intake Flomaster cat back
Car still available, probably gonna insure it and drive it for a month or two while the weather is nice.
Anyone interested?
Anyone interested?
#13
MJ>XJ
Join Date: Mar 2009
Location: Griffin, G.A.
Posts: 17,836
Likes: 0
Received 4 Likes
on
3 Posts
Year: 1990
Model: Comanche
Engine: 4.0 I6
i want a fast toy so bad myself man... soon the built cummins will be sold and everything i have will be slow... lol... youve been trying to sell it for awhile now i see... but! still need item location in the thread please... lol... and best of luck man... craigslist will be your best bet...
#14
Seasoned Member
Thread Starter
Join Date: Apr 2009
Location: Northeast PA
Posts: 288
Likes: 0
Received 0 Likes
on
0 Posts
Year: 1997
Model: Cherokee
Engine: 4.0, k&n intake Flomaster cat back
yea my bad, it says NEPA in my avatar thingy, but to be more specific its located in Taylor PA 18517, 5min outside of scranton
#15
Seasoned Member
Thread Starter
Join Date: Apr 2009
Location: Northeast PA
Posts: 288
Likes: 0
Received 0 Likes
on
0 Posts
Year: 1997
Model: Cherokee
Engine: 4.0, k&n intake Flomaster cat back
i want a fast toy so bad myself man... soon the built cummins will be sold and everything i have will be slow... lol... youve been trying to sell it for awhile now i see... but! still need item location in the thread please... lol... and best of luck man... craigslist will be your best bet...
yea been kinda tryin to sell it for a while, had it on craigslist like a few months ago but didnt hear anything. also using a public computer so i cant really save pics on it. might try an autolocater or somthin like that