White Shadow
#1
CF Veteran
Thread Starter
White Shadow
So I bought my own Jeep XJ in August of 2012, since my son will be headed of to collage next year and taking his XJ with him.
It is a 5 spd. With 4.0
It has the Dana 30 and Dana 35
33" MTR's
A nice winch bumper.
Here is a list of things I want to do.
Get new 3" leaf springs from Rusty's
1.5" shackles
Warn winch
Install the sliders a friend gave me off his 2-dr XJ after he installed his long arm kit.
Want to get a Ford 8.8 axle
Change gears to 456
Cable lockers for rear end
Under armor (skid plates)
I would like to get a Rubican Transfer case or re-gear a 231 to the same.
There are a lot of cosmetic things I would like to do also but it really isn't in bad shape just a few surface rust spots, minor dings and small dents. (But I promised to help get my sons quarter panel and paint job done first).
Until i get some of the drive train stuff done I will not push it too hard. Here are a few Photos'
It is a 5 spd. With 4.0
It has the Dana 30 and Dana 35
33" MTR's
A nice winch bumper.
Here is a list of things I want to do.
Get new 3" leaf springs from Rusty's
1.5" shackles
Warn winch
Install the sliders a friend gave me off his 2-dr XJ after he installed his long arm kit.
Want to get a Ford 8.8 axle
Change gears to 456
Cable lockers for rear end
Under armor (skid plates)
I would like to get a Rubican Transfer case or re-gear a 231 to the same.
There are a lot of cosmetic things I would like to do also but it really isn't in bad shape just a few surface rust spots, minor dings and small dents. (But I promised to help get my sons quarter panel and paint job done first).
Until i get some of the drive train stuff done I will not push it too hard. Here are a few Photos'
#3
CF Veteran
Thread Starter
Thanks, Dino's
My son and I have had some really good bonding time working on his XJ. Now that I got mine I have already done several repairs to it. (Small ones like the Alternator, front U-Joints, dash lights that were burned out). But this thing needs very little as far as needing anything to make it road worthy.
We are going to do the brake up-grade soon I have two sets of the 1995 brake Master cylinder/brake booster for our XJs’. I will just need to gather all the hardware to do it.
My son and I have had some really good bonding time working on his XJ. Now that I got mine I have already done several repairs to it. (Small ones like the Alternator, front U-Joints, dash lights that were burned out). But this thing needs very little as far as needing anything to make it road worthy.
We are going to do the brake up-grade soon I have two sets of the 1995 brake Master cylinder/brake booster for our XJs’. I will just need to gather all the hardware to do it.
#4
Seasoned Member
Join Date: Jul 2010
Location: NE FL
Posts: 337
Likes: 0
Received 0 Likes
on
0 Posts
Year: 1997
Model: Cherokee
Engine: 4.0
Thats a good looking XJ! Saw you thread over on the other forum too. This forum seems to be more active. You should update it here as well.
#5
CF Veteran
Thread Starter
Long overdue. (up-date)
So since I have had my XJ. Here is a list of some of the things I have done.
Swapped in my son's axles from his old XJ.
Dana 30 & Chrysler 8.25 W/3.55 gears
Did the '95 brake booster upgrade.
Complete front and back brake job, complete with new drums, rotors, calipers, hardware and drum brake wheel cylinder.
X-long brake lines.
New stereo.
Used Currie 1-ton steering system.
Off-set rims with 31"Km2's
Hood vents from Gary Briggs. (here on this site)
List of things in the near future. (winter projects)
Dakota steering up-grade with high volume steering pump.
Front end frame rail stiffening plates from Rusty's
Steering Gearbox Spacer from IronRock OffRoad
Re-do my head liner.
Wish List;
Install my Ford 8.8 limited slip.
with this kits (XJ Ford 8.8 Axle Swap Kit) from IronRock OffRoad
Re-gear 4.56 with Eaton E-Locker for the Danna 30
SYE and driveshaft from Tom Woods
Winch for the front end.
Oh God the list is never ending right?
Swapped in my son's axles from his old XJ.
Dana 30 & Chrysler 8.25 W/3.55 gears
Did the '95 brake booster upgrade.
Complete front and back brake job, complete with new drums, rotors, calipers, hardware and drum brake wheel cylinder.
X-long brake lines.
New stereo.
Used Currie 1-ton steering system.
Off-set rims with 31"Km2's
Hood vents from Gary Briggs. (here on this site)
List of things in the near future. (winter projects)
Dakota steering up-grade with high volume steering pump.
Front end frame rail stiffening plates from Rusty's
Steering Gearbox Spacer from IronRock OffRoad
Re-do my head liner.
Wish List;
Install my Ford 8.8 limited slip.
with this kits (XJ Ford 8.8 Axle Swap Kit) from IronRock OffRoad
Re-gear 4.56 with Eaton E-Locker for the Danna 30
SYE and driveshaft from Tom Woods
Winch for the front end.
Oh God the list is never ending right?
Trending Topics
#10
CF Veteran
Thread Starter
Tail Lights
The clear tail light were already on my XJ when I bought it. I have seen them on a sight some were. They are pretty pricy though.
#11
Member
Join Date: Sep 2014
Location: Mountain Town, USA
Posts: 180
Likes: 0
Received 0 Likes
on
0 Posts
Year: 1991
Model: Cherokee (XJ)
Engine: 4.0 6 Cyl
Nice 2 door my man!
I actually really like the white and pinstripe, especially with the clear front and rear lights.
That shot of it in the mountains is awesome looking!
So honest opinion.....what are your thoughts on the KM2's? How do they handle the snow both on and off the road?
I actually really like the white and pinstripe, especially with the clear front and rear lights.
That shot of it in the mountains is awesome looking!
So honest opinion.....what are your thoughts on the KM2's? How do they handle the snow both on and off the road?
#12
CF Veteran
Thread Starter
Km2's
Honestly I can't give you a good evaluation on them. Off road they have been great and do real good snow wheeling but I don't trust them on the icy streets. I don't drive my XJ during adverse weather much. I drive my truck to do snow removal. You can manage with them but I really want to buy some Pro-Comp AT's because they are stud-able and I want to buy 6 and stud two of them. But I really need to go ahead and use these up or find someone who can use them if I can muster an extra $1,200.00 lying around.
#13
CF Veteran
Thread Starter
Up-grades
So after wheeling in the snow a few weekends ago, I was forced to get those plates installed 'cause of the crack that developed by the steering box. I really wanted to stiffen before something like that happened.
#14
CF Veteran
Thread Starter
Up-grades
So while I am at it I figured I should take care of as much as I can afford to.
Hockey-puck bump-stops, Motor mounts, steering box brace and bull-nose to protect my winch.
Hockey-puck bump-stops, Motor mounts, steering box brace and bull-nose to protect my winch.