Bright Red 97 XJ Build
#826
Senior Member
Thread Starter
Join Date: Jul 2014
Location: Glen Ellyn, IL
Posts: 931
Likes: 0
Received 0 Likes
on
0 Posts
Year: 1997
Model: Cherokee
Engine: 4.0 Inline 6
35s on! Already trimmed a bit off the back of the inner fender to clear full lock. Not planning to wheel with this current setup. I have everything except the long arms and rear driveshaft for the new setup.
#828
Senior Member
Thread Starter
Join Date: Jul 2014
Location: Glen Ellyn, IL
Posts: 931
Likes: 0
Received 0 Likes
on
0 Posts
Year: 1997
Model: Cherokee
Engine: 4.0 Inline 6
yeah. I need to get up and go find red doors and pick up my sliders to cut out what's left of the rockers. That's the ugly side, why do you think all my pictures show the other lol. It's 3.5" front and ~4" rear.
#829
Senior Member
Thread Starter
Join Date: Jul 2014
Location: Glen Ellyn, IL
Posts: 931
Likes: 0
Received 0 Likes
on
0 Posts
Year: 1997
Model: Cherokee
Engine: 4.0 Inline 6
Trying to diagnose this death wobble I've been having the past month. I tighten up that ball joint that I had issues with at Winterfest, but that only made things worse. I'm gonna go through and triple check every nut and bolt under there and hopefully I won't **** myself after hitting a bump at 40mph.
#830
Seasoned Member
Trying to diagnose this death wobble I've been having the past month. I tighten up that ball joint that I had issues with at Winterfest, but that only made things worse. I'm gonna go through and triple check every nut and bolt under there and hopefully I won't **** myself after hitting a bump at 40mph.
Also, get an alignment.
#831
Senior Member
Thread Starter
Join Date: Jul 2014
Location: Glen Ellyn, IL
Posts: 931
Likes: 0
Received 0 Likes
on
0 Posts
Year: 1997
Model: Cherokee
Engine: 4.0 Inline 6
Torqued my TREs, knuckles, track bar, track bar bracket, and greased everything and it still wobbles bad after hitting bumps at 40mph. I'm pretty sure that incident when the ball joint blew (and general abuse offroad) dicked the inner C of the axle, which is why the upper ball joint won't sit flush anymore and is causing the wobble. I can feel it start on the drivers side. I can either weld the joint in or swap in another D30. I found an HP housing on Craigslist for $100 a couple hours away so hopefully the seller gets back to me.
#832
Senior Member
Thread Starter
Join Date: Jul 2014
Location: Glen Ellyn, IL
Posts: 931
Likes: 0
Received 0 Likes
on
0 Posts
Year: 1997
Model: Cherokee
Engine: 4.0 Inline 6
Picked up the axle. HP D30 housing out of a '98 with 3.55 gears. I just plan to clean it up, paint it, new axle seals, new ball joints, and new pinion seal. I need to get my jeep to drive safely again so I have no time for a project axle right now. I'm swapping over everything from my axle (gears, locker, knuckles, shafts, and hubs) and while it's out I'm doing the oil pan gasket and the leaky rear main seal.
#833
Senior Member
Thread Starter
Join Date: Jul 2014
Location: Glen Ellyn, IL
Posts: 931
Likes: 0
Received 0 Likes
on
0 Posts
Year: 1997
Model: Cherokee
Engine: 4.0 Inline 6
Axle's all cleaned up. Ball joints, knuckles, and gears removed. Just have to cut off the end links and it'll be ready for paint.
#836
Senior Member
Thread Starter
Join Date: Jul 2014
Location: Glen Ellyn, IL
Posts: 931
Likes: 0
Received 0 Likes
on
0 Posts
Year: 1997
Model: Cherokee
Engine: 4.0 Inline 6
Twinning lol. This axle had some wierd standard sized lower ball joint nut on it and was a pain looking for a socket to fit, was like a 1" 1/8 or something.
#837
CF Veteran
Join Date: Oct 2013
Location: Greenville, SC
Posts: 5,920
Likes: 0
Received 190 Likes
on
165 Posts
Year: 1999
Model: Cherokee(XJ)
Engine: 4.0
Originally Posted by Doove
Twinning lol. This axle had some wierd standard sized lower ball joint nut on it and was a pain looking for a socket to fit, was like a 1" 1/8 or something.
#839
CF Veteran
Join Date: Oct 2013
Location: Greenville, SC
Posts: 5,920
Likes: 0
Received 190 Likes
on
165 Posts
Year: 1999
Model: Cherokee(XJ)
Engine: 4.0
Originally Posted by Joecam18
Noted!