Those that have hockey puck bump stops, how many?
#1
Senior Member
Thread Starter
Join Date: Jul 2011
Location: Chuluota
Posts: 671
Likes: 0
Received 0 Likes
on
0 Posts
Year: 2001
Model: Cherokee
Engine: 4.0
Those that have hockey puck bump stops, how many?
Just put on my 33s, and they appear to want to eat my fenders.
I currently had 1 hockey puck that worked great for my 31s . I was going to add some more, look likes 3 total is all I can fit and it will still be tight.
1. For those that run pucks up front how many do yo run with the stock upper bump?
2. Did you drill and bolt them in or was epoxy enough? I liquid nailed the 1 in just not sure a stack would hold under stress. Also do not really want to remove the coil on the passenger side just to add hockey pucks. lol
Thanks
I currently had 1 hockey puck that worked great for my 31s . I was going to add some more, look likes 3 total is all I can fit and it will still be tight.
1. For those that run pucks up front how many do yo run with the stock upper bump?
2. Did you drill and bolt them in or was epoxy enough? I liquid nailed the 1 in just not sure a stack would hold under stress. Also do not really want to remove the coil on the passenger side just to add hockey pucks. lol
Thanks
#3
Junior Member
Join Date: Nov 2011
Location: GVRD, B.C. Canada
Posts: 91
Likes: 0
Received 0 Likes
on
0 Posts
Year: 1993
Model: Cherokee
Engine: 4.0
Your tires radius is 1 inch greater than before, a hockey puck is 1 inch thick.
Add one puck and flex it out again and make sure your clearance is good accounting for the fact that different tire brands are different height compared to their advertised size.
Add one puck and flex it out again and make sure your clearance is good accounting for the fact that different tire brands are different height compared to their advertised size.
#5
Senior Member
Thread Starter
Join Date: Jul 2011
Location: Chuluota
Posts: 671
Likes: 0
Received 0 Likes
on
0 Posts
Year: 2001
Model: Cherokee
Engine: 4.0
Why does that flex pic look like it was taken on a well kept tax payer funded piece of land?
Installed, test tonight to see if 3 is good or can go down to 2...
#6
So did you just bolt those together, flex the heck out of the jeep, unbolt the spring keeper and slide that in there? How are you holding it in place? I need to bumpstop a bit more but like you said, I REALLY don't want to remove those coils again haha.
#7
Senior Member
Thread Starter
Join Date: Jul 2011
Location: Chuluota
Posts: 671
Likes: 0
Received 0 Likes
on
0 Posts
Year: 2001
Model: Cherokee
Engine: 4.0
Drilled pucks, and test fit on bench, then popped them in one at a time, and dropped the bolt in. Driver side was able to drill hole from bottom, passenger just glued in.
Trending Topics
#8
Senior Member
Join Date: Nov 2010
Location: Vegas Baby!
Posts: 922
Likes: 0
Received 0 Likes
on
0 Posts
Model: Cherokee
I've got a 6.5" lift with 33"s and I use 5 pucks on each side. I gorilla glued them together and to the base, the glue didnt hold on the metal. Then I JB WELDED them in, works great
Thread
Thread Starter
Forum
Replies
Last Post
rdr8887
Stock XJ Cherokee Tech. All XJ Non-modified/stock questions go here
11
01-27-2020 09:24 AM
her89
Stock XJ Cherokee Tech. All XJ Non-modified/stock questions go here
9
09-26-2015 12:06 PM
nicksan
Stock XJ Cherokee Tech. All XJ Non-modified/stock questions go here
18
09-25-2015 03:52 PM
Currently Active Users Viewing This Thread: 1 (0 members and 1 guests)