Rock Krawler X Factor 3 link Long Arm
#1
Member
Thread Starter
Join Date: Jan 2013
Location: Beech Creek, Pennslvania
Posts: 124
Likes: 0
Received 0 Likes
on
0 Posts
Year: 1998
Model: Cherokee
Engine: 4.0
Rock Krawler X Factor 3 link Long Arm
Is anyone running this kit on the road? My jeep is still a DD and I want a good stable 3 link kit and have been drooling over this one for a while.. Is it stable on the road and in of camber situations? I've read the reviews but they are almost all just trail reviews. Any info would be greatly appreciated.
#3
Seasoned Member
Join Date: Apr 2011
Location: Yuma
Posts: 420
Likes: 0
Received 1 Like
on
1 Post
Year: 1993
Model: Cherokee
Engine: 4.0, APN header & 2.5" exhaust
I am running it with 8 inches of lift on a daily driver with no sway bars. It's legit. Drives 75 mph on the highway for hours without a hiccup. I plan on going down to 6.5" tho just for the sake of not being so damn tall..
#6
CF Veteran
Join Date: Nov 2008
Location: mass
Posts: 1,021
Likes: 0
Received 3 Likes
on
2 Posts
Year: 1992
Model: Cherokee
Engine: 4.0 high output
I've been running it for about 2 months and am really happy with it. DD weekend warrior.
I did hd frame stiffeners first then welded in the crush sleeves and control arm mounts. Also boxed in the axle side mounts. The arms are beef and the new joints are greaseable.
I did hd frame stiffeners first then welded in the crush sleeves and control arm mounts. Also boxed in the axle side mounts. The arms are beef and the new joints are greaseable.
Last edited by xjheep92; 04-02-2014 at 10:17 PM.
Trending Topics
#8
Resident Zombie Hunter
Join Date: Aug 2010
Location: Virginia
Posts: 3,542
Likes: 0
Received 2 Likes
on
2 Posts
Year: 1997
Model: Cherokee
Engine: 4.0L
It feels a bit like a water bed but once you get used to it it's not a problem. It's not too bad. If you don't like it you can always order the fourth link and do that.
#10
CF Veteran
Join Date: Nov 2008
Location: mass
Posts: 1,021
Likes: 0
Received 3 Likes
on
2 Posts
Year: 1992
Model: Cherokee
Engine: 4.0 high output
It feels very stable on the road. The crush sleeves were the hardest part. It's not easy to drill 4 big *** holes through the frame stiffeners and unbody rail. Now that it's done it was totally worth it tho
#12
Former Sponsor
Join Date: Feb 2010
Location: Hesperia
Posts: 2,021
Likes: 0
Received 1 Like
on
1 Post
Year: 89
Model: Cherokee
Engine: 4.0
looks like you should drill the holes for those sleeves first, that would be easier than immediately install stiffeners after. Assuming you can align the holes in the stiffeners perfectly with the unibody rail.
#15
Newbie
Join Date: Nov 2013
Location: PNW
Posts: 9
Likes: 0
Received 0 Likes
on
0 Posts
Year: 2000
Model: Cherokee
Engine: 4.0l
My neighbor has it and loves it. He said he had to get a antirock antisway because it flexed so much on the trail, and up in the pnw we have trees EVERYWHERE. He also has full frame stiffeners, is sitting at about 6, with 35's. Its his daily driver and weekend trail rig.