Getting more lift out of a RE 3.5 lift kit ..
#1
Member
Thread Starter
Join Date: Jun 2010
Location: southern california
Posts: 127
Likes: 0
Received 0 Likes
on
0 Posts
Year: 1998
Model: Cherokee
Engine: HO 4.0
Getting more lift out of a RE 3.5 lift kit ..
Hello everyone . I have a RE 3.5 kit with full leaf pack installed on my XJ . I am trying to get more lift out of it to run 32" tires with the stock fenders .
here is my idea :::
using the RE shackles that give an extra 1.25" in the rear and replacing my 3.5" coil springs with RE 4.5 coils .
What do you guys think ??? Think it will work ??
I do not want to use leaf spring riser blocks ......
Thanks !
here is my idea :::
using the RE shackles that give an extra 1.25" in the rear and replacing my 3.5" coil springs with RE 4.5 coils .
What do you guys think ??? Think it will work ??
I do not want to use leaf spring riser blocks ......
Thanks !
#3
Member
Thread Starter
Join Date: Jun 2010
Location: southern california
Posts: 127
Likes: 0
Received 0 Likes
on
0 Posts
Year: 1998
Model: Cherokee
Engine: HO 4.0
i know trimming is an option , but looking to get more lift as well ..
so back to my question above ::
would this idea work ??
Thanks again guys .
so back to my question above ::
would this idea work ??
Thanks again guys .
#4
Senior Member
Join Date: Feb 2011
Location: Lawrenceville
Posts: 807
Likes: 0
Received 0 Likes
on
0 Posts
Year: 1995
Model: Cherokee
Engine: 4.0L I-6
Yea why wouldnt it? Or you could get coil spacers for the front. Heck you could even get 2 inch shackles for the rear, those 4.5 inch coils and a 1inch coil spacer.. And get you up another 2inches all the way around.. Just sayin
#5
Your control arm angles will be all wrong and your front axle will get pulled back.
Invest in new adjustable upper and lower control arms or a long arm upgrade if you go that high.
Invest in new adjustable upper and lower control arms or a long arm upgrade if you go that high.
#6
Member
Thread Starter
Join Date: Jun 2010
Location: southern california
Posts: 127
Likes: 0
Received 0 Likes
on
0 Posts
Year: 1998
Model: Cherokee
Engine: HO 4.0
I undrstand what you are saying about the control arms . but the RE 4.5 kit comes with the fixed arms, and that is about the hight it will be sitting at if this all works out ... so i think the fixed arms should work .. correct me if im wrong ..
Trending Topics
#9
Member
Thread Starter
Join Date: Jun 2010
Location: southern california
Posts: 127
Likes: 0
Received 0 Likes
on
0 Posts
Year: 1998
Model: Cherokee
Engine: HO 4.0
actualy you are wrong about that ... check the RE site .... both fixed arms are the same for 3.5" and 4.5" . part# RE3700.
so with this a known fact now.... what do you think ??? lol
so with this a known fact now.... what do you think ??? lol
#10
Member
Thread Starter
Join Date: Jun 2010
Location: southern california
Posts: 127
Likes: 0
Received 0 Likes
on
0 Posts
Year: 1998
Model: Cherokee
Engine: HO 4.0
AeroSynch :: how much fender trimming did you need to do ??? and do you get any wheel rub at full flex/lock ? thanks
#11
CF Veteran
Join Date: Sep 2010
Location: NC
Posts: 1,843
Likes: 0
Received 0 Likes
on
0 Posts
Year: 1998
Model: Cherokee
Engine: 4.0 L
Yeah I'd say that it would work.. You'd prob just want to do an inch or so though cause you don't want to have to get longer shocks too. I assume you already have a sye and driveshaft right?
#12
Member
Thread Starter
Join Date: Jun 2010
Location: southern california
Posts: 127
Likes: 0
Received 0 Likes
on
0 Posts
Year: 1998
Model: Cherokee
Engine: HO 4.0
yup i got a SYE and CV drive shaft ... also i decided against the RE shocks that came with the kit and am running adjustable shocks with more travel than the RE shocks . i think i will be okay with the shocks, if not i've had my eye on the new bilstein 5160s =)