extend bumpstops, how to exactly
#1
CF Veteran
Thread Starter
Join Date: Oct 2012
Location: Orlando/Winter Garden
Posts: 1,277
Likes: 0
Received 0 Likes
on
0 Posts
Year: 1998
Model: Cherokee
Engine: I6
extend bumpstops, how to exactly
If your runnin big tires you should measure to bumpstop accordingly..so, iv searched a bit and all i find is fixed length bumpstops, so how would you extend bumpstops to precise measurements? Iv heard of hokey (lol) pucks but for the front?
#2
Senior Member
Join Date: Aug 2011
Location: pennsylvania
Posts: 607
Likes: 0
Received 0 Likes
on
0 Posts
Year: 1999
Model: Cherokee
Engine: 4.0L
I used softballs in my front coils and they turned out to be perfect size. In the back I bought daystar extended bumpstops and bolted them to some 2x4x1/4 box that I welded to the framerail.
#5
Moderator of Jeeps
Join Date: Jul 2011
Location: Frederick, MD from Cleveland, OH
Posts: 21,029
Likes: 0
Received 3 Likes
on
3 Posts
Year: 1993 YJ Wrangler
Engine: 4.0 I6
Hockey pucks are for the front. You drill a hole in the center of the coil bucket and through the centers of as many hockey pucks as you need. Drop a bolt through the top with a nut under the bucket, and you have bumpstops.
#6
Seasoned Member
Join Date: Jan 2013
Location: SoCal
Posts: 447
Likes: 0
Received 1 Like
on
1 Post
Year: 1994
Model: Cherokee
Engine: 4.0
I'm using pucks in the front. Mine are bolted to the spring perch with a 5/16" bolt. IIRC, I had to tap one of them since the bottom of the perch wasn't accessible.
Last edited by sreeb; 12-19-2013 at 12:02 AM.
#7
Member
Join Date: Jul 2012
Location: The corner of Grey St.
Posts: 167
Likes: 0
Received 0 Likes
on
0 Posts
Year: 1996
Model: Cherokee
Engine: 4.0L
For the front, use hockey pucks inside the coils. The way I did it was to remove the coils and drill and tap for a 5/16" bolt in the center of the coil bucket on the axle. Take however many pucks you are going to need and drill a 5/16" hole in the center. Then take two pucks and drill a larger hole partially into them to countersink the bolt heads. Slide the pucks into the coild and then put the bolt in them and tighten them down. Also, a more temporary method, but one I used for a couple months without issues was to just rtv the coils in place.
Trending Topics
#11
You can just glue the hockey pucks on using shoo goo. Scuff the pucks and clean the rust off the base. NEVER had one come off using shoo goo.
#13
CF Veteran
Join Date: Dec 2012
Location: York, PA
Posts: 4,169
Likes: 0
Received 6 Likes
on
6 Posts
Year: 1998
Model: Cherokee
Engine: 4.0
I'm doing hockey pucks on the front of mine. Seems there's plenty of room to get a nut under the coil bucket. Basically same way as above. For the rear, I plan on getting the 4" stops for the upper unirail, and possibly welding extensions onto the spring plates to catch it on if that isn't enough.
#14
So I figured if they fell off I would just bolt them on. Well that was over a year ago. Through tons of off road trips. Needless to say they have been proven to me.
#15
CF Veteran
Join Date: Mar 2012
Location: Holland MI
Posts: 1,785
Likes: 0
Received 0 Likes
on
0 Posts
Year: 2000
Model: Cherokee
Engine: 4.0
Use,
http://www.jegs.com/p/Prothane/Proth...62178/10002/-1
Softer than pucks.
There's some write ups online so I won't explain.
http://www.jegs.com/p/Prothane/Proth...62178/10002/-1
Softer than pucks.
There's some write ups online so I won't explain.