What did you do to your Cherokee today?
04-06-2009, 08:33 AM
#2822
04-06-2009, 10:42 AM
#2823
Senior Member
Join Date: Oct 2008
Location: Orlando FL.
Posts: 544
Likes: 0
Received 0 Likes
on
0 Posts
Year: 1996
Model: Cherokee
Engine: 242 6cyl
Just got off the phone with Rough Country ordering my lift should be here wed. and it should be on by friday/saturday......
04-06-2009, 05:29 PM
#2826
Senior Member
Join Date: Oct 2008
Location: Orlando FL.
Posts: 544
Likes: 0
Received 0 Likes
on
0 Posts
Year: 1996
Model: Cherokee
Engine: 242 6cyl
04-06-2009, 05:36 PM
#2827
Newbie
Join Date: Mar 2009
Posts: 13
Likes: 0
Received 0 Likes
on
0 Posts
Model: Cherokee
Took off body side moldings
Removed the molding today. I was surprised how easy they peeled off. The tape holding them on was a little bit of work to remove. We used heat gun and Goof Off. It looks sooooooo much better without those things!! Also much easier to clean.
04-06-2009, 08:32 PM
#2829
Senior Member
Join Date: Dec 2008
Location: Norco CA.
Posts: 510
Likes: 0
Received 0 Likes
on
0 Posts
Year: 1991 XJ SPORT 2 DR.
Model: Cherokee
Engine: 4.0 600 HP
Over the past 3 days. Pulled the head hoping to replace the head gasket, heads cracked. Found a motor on craigslist in richmond, pulled it yesterday morning. Pulled mine yesterday after noon, then fed my help plenty of beer and burgers. I may get it back together this week. 
looks great wish i had a tube bender i want one
04-06-2009, 11:30 PM
#2830
Member
Join Date: Oct 2007
Posts: 153
Likes: 0
Received 0 Likes
on
0 Posts
Year: 1987
Model: Cherokee
Engine: 4.0
04-06-2009, 11:33 PM
#2831
Senior Member
Join Date: Dec 2008
Location: Washington State
Posts: 990
Likes: 0
Received 2 Likes
on
2 Posts
Year: 1996
Model: Cherokee
Engine: 4.0L HO
Made the stupid mistake of cutting my door wires to remove the doors. Good thing I know how to solder/shrink wrap, hahaha. Luckily I only did the drivers door. When I looked at them to cut them I seen that the PO had cut 2 wires, the one that rolls the pass rear window up and the one that locks the door. So at least I didnt cut them for no reason. After I soldered them up everything works great.
04-07-2009, 03:30 AM
#2833
Seasoned Member
Join Date: Mar 2009
Posts: 290
Likes: 0
Received 0 Likes
on
0 Posts
Year: 91
Model: Cherokee
Engine: 4.0
well i have not done any work on my 91 xj, but over the past two months i have spent a hole lot on it. here is the list as of now,
araid cold air intake (installed home on leave)
poweraid throttle body spacer (installed on leave)
banks tourque tube header
dynomax cat. converter
dynomax muffler w/ tail pipe
jks cross mem w/ t case skid
currie steering system
rubicon express drop pitman arm
2 rubicon express e-duty 4.5" rear leafs
still need to get
jks adj. front coil spacer
control arm drop kit
and the list go's on and on and on later dudes
araid cold air intake (installed home on leave)
poweraid throttle body spacer (installed on leave)
banks tourque tube header
dynomax cat. converter
dynomax muffler w/ tail pipe
jks cross mem w/ t case skid
currie steering system
rubicon express drop pitman arm
2 rubicon express e-duty 4.5" rear leafs
still need to get
jks adj. front coil spacer
control arm drop kit
and the list go's on and on and on later dudes
