What Axle is this? D60 or D44
#5
CF Veteran
Thread Starter
Join Date: Apr 2009
Location: Jacksonville, FL
Posts: 1,097
Likes: 0
Received 1 Like
on
1 Post
Year: 1989
Model: Cherokee
Engine: 4.0L
did not find a 60 but we did find a serial number we think. It was
CIR7xd1604a402-2NA Can anyone figure it out from that?
Found a
4156
C36 63?
81 or 61?
Thanks
CIR7xd1604a402-2NA Can anyone figure it out from that?
Found a
4156
C36 63?
81 or 61?
Thanks
#6
CF Veteran
Join Date: May 2008
Location: Bristol,Pa
Posts: 5,188
Likes: 0
Received 6 Likes
on
6 Posts
Year: 94
Model: Cherokee
Engine: 4.0L
I think that long series is your BOM.. was it on the tube?
Go here...
http://www.pirate4x4.com/tech/billavista/60_front/
Go here...
http://www.pirate4x4.com/tech/billavista/60_front/
Trending Topics
#9
CF Veteran
Thread Starter
Join Date: Apr 2009
Location: Jacksonville, FL
Posts: 1,097
Likes: 0
Received 1 Like
on
1 Post
Year: 1989
Model: Cherokee
Engine: 4.0L
The reason I asked this ? is b/c we were installing a full spool today with 5.13 gears. Pinion went in fine. The Spool though when we installed was about 1/4" away from the pinion. The only way we could get it to touch the pinion was to space the ring gear out with some washers. Now, we know we can not install it that way we were just testing. What we were thinking is that we got the wrong spool like the 4.56 and down one instead of the 4.56 up spool. Anyones opinions?
#11
CF Veteran
Thread Starter
Join Date: Apr 2009
Location: Jacksonville, FL
Posts: 1,097
Likes: 0
Received 1 Like
on
1 Post
Year: 1989
Model: Cherokee
Engine: 4.0L
I have been doing some research. It actually sounds like I have a dana 61 which had the pinion spaced over more b/c of the running a 3.07 gear ratio. So we now have some problems b/c from what I read you can not put this set up in the axle. Now, I guess we search for a dana 60.
#12
CF Veteran
Join Date: Feb 2010
Location: Soddy Daisy TN
Posts: 5,420
Likes: 0
Received 0 Likes
on
0 Posts
Year: 97
Model: Cherokee
Engine: 4.0L
Did some searching and looks like you can get a ring gear spacer to make it work. Good chance you have some oddball 31 spline shafts that will need to be replaced to use the 30 or 35 spline spool. Ballistic Fab can make the spacer for you.
#13
CF Veteran
Thread Starter
Join Date: Apr 2009
Location: Jacksonville, FL
Posts: 1,097
Likes: 0
Received 1 Like
on
1 Post
Year: 1989
Model: Cherokee
Engine: 4.0L
Oh we checked that before we ordered the spool. its 30 spline
Last edited by 89whiteXJ; 08-09-2010 at 06:31 AM.
#14
CF Veteran
Thread Starter
Join Date: Apr 2009
Location: Jacksonville, FL
Posts: 1,097
Likes: 0
Received 1 Like
on
1 Post
Year: 1989
Model: Cherokee
Engine: 4.0L
Ok we ordered the spacer and then after talking to people we also got the pass side of the spool milled down 1/8" so the bearing would sit in further and shift the spool Rt. Then we also ordered a spacer for the Left side to take up for it. now in total we are moving the ring gear over 7/16" So, That should work. I will post results.
Thread
Thread Starter
Forum
Replies
Last Post
FS[SouthCent]: 4.56 gear set and master install kits D30 and D44
dcollins3208
Axles/Tires/Wheels
12
12-11-2015 11:49 AM
64dodge
Stock Grand Cherokee Tech. All ZJ/WJ/WK Non-modified/stock questions go here!
3
09-30-2015 05:50 PM
Currently Active Users Viewing This Thread: 1 (0 members and 1 guests)