|
havent updated this in a long while but last night i spent hours getting dirty and cursing Chrysler products
few months back the overflow nipple on the top of the radiator broke off but no big deal becuase previous owner bought a lifetime one from pep boys...cool right? so i pull out the old radiator head to pep boys, grab a gallon of coolant and exchange the radiator. easy peasy. drop the new one in and flush out the system. fill and drive. well a month later... what do you know the waterpump fails. -___- so pull the whole front of the engine apart to get to the waterpump. drain out that nice new coolant i just put in. head to Vato Zone to grab a new waterpump, lower rad hose, 180* thermostat and yet another gallon of coolant. replace the waterpump. replace the lower rad hose drop in the new thermostat start to tighten up the thermostat housing when i hear a little noise and of course the f-ing thing dropped out slightly and now i just cracked the housing. so back to the parts house i go. thankfully they had one in stock. get back home and dont take any chances and i put a little dab of permatex on the top so it will hold it in the groove as i put the housing on. once again button everything up and fill up with new coolant/distilled water that brings me to yesterday. in the morning after the GF left for work i went to walk the dog and i notice a leak trail from our parking spot out to the street. great.... https://www.vwvortex.com/Anthony/Smilies/facepalm.gif i text her to look over the truck and monitor the gauges on her short drive home from work and ill address everything when i get home that afternoon. so i get home and notice that the line fitting from the pressurized hard line to the transmission is leaking substantially. ugh. call around and have to go to a pretty far parts house to grab the new line fitting but thats fine so i hop on the harley and grab the part after work. SUCCESS!!! get home and 10 min later the new fitting is on and the leak is gone. just topped up the ATF and im in business. before i decide to enjoy the rewarding feeling of having accomplished this fix in record time i decide to check for other leaks...starting at the front of the engine. well well well. what do i see but a little green crusty spot on the lower rad hose...MOTHER FUUUUUUUUUU further inspection yields that its literally sliced about an inch long but has not yet gone completely through the hose. wow close call. wouldnt want to send the GF driving and have this thing catastrophically detonate like some kind of roadside IED so yet again i call the local autozone (where i originally purchased the hose less than 2 months ago) they tell me they have another in stock but hoses arent warrantied. so ok i get it ill buy the new hose and yet another gallon of coolant and be on my way get home and pull the lower hose and yet again watch that liquid gold spill from the radiator and WP. and here is where i messed up. i actually thought..."man this kinda sucks but at least these are both easy fixes and ill be done in no time" WRONG! i go to put the clamps on the new hose and what do i see...ANOTHER 1" SLICE so now im irritated. i call up the same autozone and they said they dont have any more but direct me to another store with one. get there and wait in line for 15 min(not exaggerating) thankfully i get helped by the store manager who grabs the hose i need after i explain what is going on and wouldnt you know... SLICED 1" LONG but again not all the way through. regardless im not putting that on the XJ so i ask him to grab another...nope thats it. so he calls another store and finds one for me and asked them to verify its in good shape. boom this saga is finally over. so i drive another ten min further and go inside and wait in line again. get to the counter...seriously i sh!t you not. guess what. ANOTHER SLICE. IM ABOUT TO LOSE MY MIND. LIKE SERIOUSLY WHO KEEPS OPENING THESE BOXES WITH RAZORS?!?!?! OR MAYBE THEY JUST HIRE SOMEONE FULL-TIME TO GO TO EACH STORE AND MAKE SURE THEY SABOTAGE ALL THE JEEP RADIATOR HOSES at this point im fed up. i call up oreily and they verify they have two at the closest store. i get there and grab the Gates Brand one, while a bit more expensive, the higher quality and lack of razor blade slices makes it worth it. so after almost an hour and 4 autozone locations in 1 day i was over this. get home. slap the new hose on. finally install that new coolant temp sensor that i picked up from rockauto but have been too lazy to install. fill it back up with coolant/water. burp the system. get it up to temp and drive it around for 10 min. park and make sure it isnt leaking anywhere. douse the thing in kerosene and light a match. the last line didnt actually happen but a guy can dream right? anyway sorry for the novel for those who read it... |
not much of an update but i supervised the GF do an oil change last nite
mopar filter/rotella t5 15w40 then i helped her change the thermostat out for a non failsafe 180* temp scored some BF Goodrich Destination A/T tires yet this was the only pic i took cause it made me laugh https://farm2.staticflickr.com/1950/...5f1b10ac_b.jpg jeep is happy once again |
and that brings us up to this past weekends adventures!
CAMPING SEASON HAS OFFICIALLY BEGUN FOR US had a chance to take off for a few days so planned a pretty simple loop up 395 through Yosemite and back down through Sequoia took a half day at work wed and left Long Beach around 1pm and reached our BLM campsite in Bishop around 630pm woke up the next morning and took in the view along with the silence https://farm2.staticflickr.com/1937/...0e06809d_b.jpg Thursday we kept heading north on 395 and pulled off to check out the June Lake Loop https://farm2.staticflickr.com/1925/...2ca61487_b.jpg then headed north to Mono Lake https://farm2.staticflickr.com/1977/...88fc2643_b.jpg and even further north to the Bodie Ghost Town https://farm2.staticflickr.com/1970/...8d42f4b9_b.jpg https://farm2.staticflickr.com/1935/...1e7025c3_b.jpg https://farm2.staticflickr.com/1902/...2f0d7d89_b.jpg https://farm2.staticflickr.com/1917/...1dc99f10_b.jpg https://farm2.staticflickr.com/1968/...575a5253_b.jpg after Bodie we headed south to Lee Vining to grab dinner on our way back to find a campsite near some natural hot springs by Mammoth Lakes saw plenty of abandoned properties on the way but this one had a great view https://farm2.staticflickr.com/1958/...6c92f088_b.jpg we ended up at the Hilltop Tub right around sunset and had a nice soak while watching the sun creep out of sight, https://farm2.staticflickr.com/1956/...0bd8bb88_b.jpg https://farm2.staticflickr.com/1979/...a4a4222c_b.jpg stayed overnight and woke up really early to watch the sun rise from the hot spring too. pretty darn refreshing to be in 100* water when its 30* outside haha https://farm2.staticflickr.com/1904/...9bd3e0a8_b.jpg woke up Friday and after some coffee headed north to Tioga Pass (9945ft) and into Yosemite NP scored a campsite at Crane Flat and had some breakfast before heading into the valley https://farm2.staticflickr.com/1923/...281a2b48_b.jpg https://farm2.staticflickr.com/1967/...81058ea9_b.jpg https://farm2.staticflickr.com/1940/...c3e84f4a_b.jpg https://farm2.staticflickr.com/1905/...c11d31c8_b.jpg https://farm2.staticflickr.com/1978/...6ced851c_b.jpg https://farm2.staticflickr.com/1957/...5313e3dc_b.jpg https://farm2.staticflickr.com/1948/...6b39ca00_b.jpg Saturday we slept in and took our time leaving and making our way down to Sequoia NP weather looked fine leaving Yosemite and even heading toward Kings Canyon/Sequoia but as we started climbing it kept getting darker and darker https://farm2.staticflickr.com/1945/...2fb82189_b.jpg when we finally arrived at the General Sherman tree we parked on the side of the road and started walking up and all of a sudden the clouds unloaded a fury of hail which quickly turned into a sleet/hail thunderstorm https://farm2.staticflickr.com/1957/...d4a3da6b_b.jpg by the time we got back to the jeep it looked like this https://farm2.staticflickr.com/1980/...d716d227_b.jpg we decided to just chill and let the storm pass and take a slow decent and find an area to stay for the night we ended up stumbling upon Horse Creek Campgrounds which had awesome views to the still lingering thunderstorm up in the mountains and a peaceful river snaking through the canyon on the west https://farm2.staticflickr.com/1919/...6599813c_b.jpg thats basically it. we woke up sunday and took our time making breakfast and coffee before making our way back to the LA area but since the XJ did so well i decided to treat it to some nice new parts new upper and lower control arms https://farm2.staticflickr.com/1975/...8b5d66fd_b.jpg NEW HEAVY DUTY LEAF SPRINGS AND BUSHINGS!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!! (FINALLY) https://farm2.staticflickr.com/1953/...970fbc36_b.jpg |
nice jeep , great pics , I think you do mere trail rids/ light wheelin with your 2wd then most the 4x4 people I know lol
|
so yet another long winded update...
last thursday we took the jeep up to the local observatory at night and on the way home i could tell it was idling different. certainly had a strange misfire to it but with no CEL. so checked for spark and had decent spark across all 6. i then unplugged each injector individually while running and when i unplugged #5 it didnt have too much of an effect on the stumble. boom so my stock oem injectors have finally given up at 160k... ordered a set of 4 hole upgrades. solved...i thought meanwhile i still gotta put on those rear leaf springs and bushings so decided to do that while we wait for injectors. here are a few pics of us doing the passenger side rear https://farm2.staticflickr.com/1945/...32e20e4b_b.jpg https://farm2.staticflickr.com/1962/...66e6b04e_b.jpg https://farm2.staticflickr.com/1961/...66c9ce25_b.jpg https://farm2.staticflickr.com/1953/...3cfe79a3_b.jpg https://farm2.staticflickr.com/1978/...39e5cfc8_b.jpg https://farm2.staticflickr.com/1977/...3248a3f4_b.jpg https://farm2.staticflickr.com/1954/...049cf08a_b.jpg https://farm2.staticflickr.com/1967/...66c9ce25_b.jpg https://farm2.staticflickr.com/1906/...3fbefa20_b.jpg boom so now that was taken care of i pulled the fuel rail in anticipation for the injectors (no pics of that but its pretty self explanatory. new injectors finally arrive and im pumped because this has all gone rather smooth and ill be able to button this back up so she can take it to work... old vs new https://farm2.staticflickr.com/1913/...a6f28e4a_b.jpg https://farm2.staticflickr.com/1979/...13c27bf6_b.jpg https://farm2.staticflickr.com/1938/...92680341_b.jpg then to be sure i tested the pressure at the rail at idle and at heavy throttle and everything seemed to check out https://farm2.staticflickr.com/1951/...1d7aabd9_b.jpg yet the stumble is still there WTF so i pull the plugs and still see a crap electrode on 4&5. so of course it is the plugs... https://farm2.staticflickr.com/1967/...9530cf2d_b.jpg https://farm2.staticflickr.com/1935/...12ddce91_b.jpg swapped them out with my spares...no change. then of course its prob the **** VatoZone distributor cap/rotor/pickup coil. well its lifetime so why not go get a replacement for free. change everything over...no change. ok so then i use my obd2 scanner and verify the TPS has good sweep voltage, the map sensor and o2 sensor are functioning correctly and i literally just cleaned the Idle Air Control Valve 2 weeks ago so there is no way its that... but i take it out and verify its clean still...everything looks good. so now reality starts to set in... i better get the compression tester out #1 https://farm2.staticflickr.com/1905/...5a3a165b_b.jpg #2 https://farm2.staticflickr.com/1962/...4d3a5b9c_b.jpg #3 https://farm2.staticflickr.com/1950/...7d12f302_b.jpg #4:banghead: https://farm2.staticflickr.com/1911/...74b06232_b.jpg #5:banghead: https://farm2.staticflickr.com/1959/...52740a3f_b.jpg #6 https://farm2.staticflickr.com/1926/...b5ff1c5f_b.jpg great. just what i wanted to deal with. so my fingers are crossed that its just the gasket that blew out and not a cracked head. i specifically avoided the 0331 head model years and bought one with the 0630 so after work yesterday i had a few hrs to start tearing this thing apart this is more of an involved job so my key was to just go slow and keep everything organized step one: remove battery leads https://farm2.staticflickr.com/1969/...086f2587_b.jpg step two: remove upper air box and intake boot https://farm2.staticflickr.com/1929/...d613f7e5_b.jpg step three: remove lower air box https://farm2.staticflickr.com/1924/...f3eb12be_b.jpg step four: remove throttle cables, electrical connectors and vacuum lines https://farm2.staticflickr.com/1953/...f3069aa0_b.jpg step five: loosen serpentine belt and pull power steering pump https://farm2.staticflickr.com/1921/...9e89c70d_b.jpg https://farm2.staticflickr.com/1960/...0892123c_b.jpg step six: pull the fuel line going to the rail, remove the 11 PITA bolts that attach the intake/exhaust manifolds intake off. https://farm2.staticflickr.com/1948/...224c0e44_b.jpg exhaust off. https://farm2.staticflickr.com/1902/...9ba7456a_b.jpg after that i started running out of daylight so i just drained the coolant and pulled the thermostat housing. i ordered some things from amazon when i went inside fel-pro gasket kit https://images-na.ssl-images-amazon....%2BNUj1OKL.jpg fel-pro head bolts https://images-na.ssl-images-amazon....L._SL1500_.jpg anti-seize https://images-na.ssl-images-amazon....L._SL1500_.jpg tonight ill pull the valve cover, rockers, pushrods and the head... fingers crossed :facepalm::facepalm::facepalm::facepalm::facepalm: :facepalm: |
this tore down pretty quick yesterday plus i even had a helper
https://farm2.staticflickr.com/1923/...d6536a3b_b.jpg https://farm2.staticflickr.com/1918/...f833a712_b.jpg she was pretty bored in the beginning because all i had her do was organize the parts :laugh: https://farm2.staticflickr.com/1968/...964a7406_b.jpg https://farm2.staticflickr.com/1970/...7d543f4c_b.jpg https://farm2.staticflickr.com/1932/...52d9a32c_b.jpg https://farm2.staticflickr.com/1936/...850f566f_b.jpg id consider this a good sign. gasket is clearly torn between 4&5. going to try and get the head to a machine shop today on lunch. i couldnt find any cracks visually but im not an expert and my eyesight is pretty poor regardless https://farm2.staticflickr.com/1904/...9bf527e5_b.jpg so at this point we'll wait and see https://farm2.staticflickr.com/1955/...633c798b_b.jpg https://farm2.staticflickr.com/1934/...79fd515b_b.jpg |
the inevitable...
https://farm5.staticflickr.com/4814/...2c71f3f1_h.jpg so now i should prob thoroughly inspect the block before ordering a new head from clearwater :banghead::banghead::banghead::banghead::banghead: :banghead::banghead::banghead::banghead: |
...i just joined and this is my favorite post, out of all the ones i seen the 48 hrs since i joined
..keepin us posted. also thats a woman ! :) lucky man |
ha thanks man!!
so to update... i was watching the UPS tracking number like a hawk friday since i was off work and in usual fashion it showed up at 6pm :banghead::banghead::banghead::banghead: by that time it was already dark and that was a wasted day...so woke up early sat and started prepping https://farm5.staticflickr.com/4813/...4b358604_h.jpg https://farm5.staticflickr.com/4841/...4de67f45_h.jpg brand spaking new head https://farm2.staticflickr.com/1958/...826bbaf4_h.jpg new vs old https://farm2.staticflickr.com/1940/...bc2e2c0b_h.jpg https://farm2.staticflickr.com/1918/...42eeddde_h.jpg https://farm2.staticflickr.com/1929/...2b2bb83e_h.jpg https://farm2.staticflickr.com/1912/...a055671f_h.jpg https://farm5.staticflickr.com/4824/...b8ecdc77_h.jpg https://farm2.staticflickr.com/1974/...b8cdabf8_h.jpg this was the most frustrating part of the whole endeavor https://farm2.staticflickr.com/1949/...3d7c002f_h.jpg https://farm5.staticflickr.com/4881/...0358e975_h.jpg https://farm2.staticflickr.com/1949/...3d7c002f_h.jpg https://farm5.staticflickr.com/4808/...cfafef3a_h.jpg https://farm5.staticflickr.com/4822/...e736a489_h.jpg https://farm5.staticflickr.com/4850/...5b612649_h.jpg https://farm5.staticflickr.com/4886/...686aee9b_h.jpg fired up just fine sat night so i was pumped...but had a little leak from the t-stat housing i needed to address but i was done for the day sunday i woke up and pulled the thermostat housing off and made sure it wasnt cracked then seated it and refilled. i also decided this would be an optimal time to do an oil change so new WIX filter and Rotella T5. we took a break and decided to hit the local LKQ yard looking for a rear washer nozzle thats no longer in production :banghead: found a 94 XJ and decided to take a chance grabbing one but once i got it home realized it didnt fit https://farm2.staticflickr.com/1975/...8d18304f_h.jpg https://farm2.staticflickr.com/1953/...03d0db8c_h.jpg finished off the afternoon with a wash/wax and LED interior bulb swap https://farm5.staticflickr.com/4874/...a5320348_h.jpg https://farm5.staticflickr.com/4863/...f95f26d1_h.jpg https://farm5.staticflickr.com/4915/...6e1c11c1_h.jpg daytime pics https://farm5.staticflickr.com/4916/...f601e794_h.jpg https://farm2.staticflickr.com/1915/...4a6cd590_h.jpg https://farm5.staticflickr.com/4870/...18cee26d_h.jpg oh and remember that leaf spring swap we did...well we didnt drive it (for obvious reasons) until the past few days and now im getting a louder than usual humming (or at least i think its louder that usual) so im going to grab some new spicer u-joints this week and see if that solves it |
Great thread. With regards to the louder humming, it could be the leaf spring bushings. When I changed the rear springs in my 99, I went with the 2-piece urethane bushings. I got a lot of road noise. So I bit the bullet and pulled out the rear springs and swapped those bushings with a set of rubber ones. Only down side is that the rubber bushings need to be pressed in....
|
so i decided to try a transmission crossmember drop because this howl only happened as a direct result of changing the leaf packs out back
that lead me to believe it may be a pinion angle issue ... yesterday after work i ran to ACE hardware and grabbed some 1" steel collars, hardened washers and longer m10x1.5 bolts. the studs pulled out really easy via the double nut method but im ashamed to admit i spent far too long trying to get the crossmember lined back up here is everything all buttoned up. *hindsight* i should have taken a few pics of the DS before because the slip yoke was another 1/8-1/4" out of the transmission tail https://farm5.staticflickr.com/4820/...7804e25c_h.jpg https://farm5.staticflickr.com/4826/...2fff6e13_h.jpg https://farm5.staticflickr.com/4905/...0d0953a2_h.jpg took it for a drive up and down the 710 freeway since it usually only made that noise while coasting around 50-65mph NO NOISE!!!! hopefully this was the issue....which would be nice because it was way easier than a pinion bearing replacement although i did also notice that the infrequent clicking from the back end is a brake shoe that is loose on the mounting plate so i ordered up some new shoes last night for $14 :laugh: the one redeeming thing about owning american stuff is that parts are dirt cheap |
awesome thread, just read through the whole thing although a little disappointing i'm caught up lol. I might be taking a trip to some of those places now they look awesome.
I keep coming back to cherokee's because they are so cheap to fix and modify, also i have done the trans brace drop a couple times but my last jeep i sprung for the $200 for the rough country sye and 4x4 front driveline and i wont do another trans drop it works much better and is easy to install |
for new years we took a trip up 395 to my buddys place in Susanville, CA...stopped at the cabin on the way up and on the way down
jeep drove flawless on the 1300 mile round trip https://farm8.staticflickr.com/7875/...4c39a211_b.jpg dropped off the remainder of the furniture at the cabin on the way up https://farm8.staticflickr.com/7879/...b6e6242b_b.jpg https://farm8.staticflickr.com/7865/...0011bc29_b.jpg https://farm5.staticflickr.com/4896/...c8872bed_b.jpg https://farm8.staticflickr.com/7873/...f97acf5d_b.jpg somewhat better shot of the new headliner https://farm5.staticflickr.com/4909/...037d7da1_b.jpg also passed this milestone https://farm8.staticflickr.com/7839/...174b561f_b.jpg https://farm8.staticflickr.com/7823/...016afe51_b.jpg also scored as much free 1890's barnwood as i could fit in the jeep...soooooooo https://farm8.staticflickr.com/7852/...d46aa2c4_b.jpg |
Why the NY plates? TN plates would give you so much more freedom to mod that thing lol
|
| All times are GMT -5. The time now is 10:39 PM. |
© 2026 MH Sub I, LLC dba Internet Brands